Industrial remote control – Core Synthesis Technology https://www.wixhc.com/cn CNC industry leader Mon, 13 Jul 2026 07:33:29 +0000 en-US hourly 1 https://wordpress.org/?v=6.8.6 Core Synthetic Industrial Wireless Remote Control DH01R-LE https://www.wixhc.com/cn/product/%e8%8a%af%e5%90%88%e6%88%90%e5%b7%a5%e4%b8%9a%e6%97%a0%e7%ba%bf%e9%81%a5%e6%8e%a7%e5%99%a8dh01r-le Mon, 13 Jul 2026 07:33:29 +0000 https://www.wixhc.com/cn/?post_type=product&p=118182

地坪机背带遥控器适用于各种地坪研磨机，采用485ModbusRTU 协议控制左右变频器的调速和前后左右控制，以及研磨电机变频器的调速和启动。左右电机采用360°摇杆操作，转弯控制更丝滑。同时支持IO控制，通讯控制，以及外部面板开关输入控制三种控制模式。

1.Adopt 433MHZ wireless communication technology，Wireless operating distance 100 meters。
2.Adopt automatic frequency hopping function，Use 32 sets of wireless remote controls at the same time，No effect on each other。
3.Supports all frequency converters with 485 modbus RTU protocol，The currently adapted inverter brands include：
Shanghai Xielin、Fuji、Huichuan、Zhongchen、INVT、Yasukawa Tatsu。If the brand is not adapted, please contact us for customization.。
4.支持研磨电机变频器调速、start up。
5.支持左右变频器调速、start up、Front and rear left and right controls。
6.支持左右变频器直线纠偏，Keep the machine moving in a straight line。
7.支持Type-C充电，5V-2A charging specifications，18650/3000mAh充电锂电池。
8.支持三种控制方式，IO接线控制，485 modbus通讯控制，外部开关输入控制。
9.采用防水设计，防水等级IP65。

Handheld terminal working voltage and current 18650/3000mAh电池-3.7V/32mA
Receiver operating voltage and current 24V/1A
Handheld transmit power 15dBm
Receiver Receive Sensitivity -100dBm
Wireless communication frequency 433Mhz frequency band
Operating temperature -25℃<X<55℃
充电接口 Type-C
Product size 285.6*139.3*129.2（mm）


Comments：
①Screen display：

②直线纠偏：
采用组合操作对左右轮速度进行纠偏，按住<纠偏使能>，旋转<Straight line correction>进行纠偏，Rotate clockwise，进行正纠偏，右轮加速，Rotate counterclockwise，进行负纠偏，右轮减速。
纠偏范围90到-90，每个纠偏值约等于0.02V电压，最大纠偏电压1.8V。

③行走控制摇杆：
摇杆前推，左右电机同时前进，松手保持前进；摇杆后推，左右电机同时后退，松手保持后退，按下<stop>按钮停止机器。
摇杆左推，左右电机左转，前半段左轮减速转弯，后半段左轮后退转弯，松手恢复直行；摇杆右推，左右电机右转，前半段右轮减速转弯，后半段右轮后退转弯，松手恢复直行。
④Power switch：
遥控器屏幕开机和关机。
⑤启动按钮：
遥控器开机后，屏幕显示启动界面，需要按下启动按钮才能进入操作界面。
注意：按下启动按钮之前，请确认所有开关处于停止位。
⑥指示灯：
工作灯：遥控器开机后，常亮红灯；
充电灯：遥控器充电时，常亮红灯，充满亮绿灯；拔掉充电线，不亮灯。
⑦研磨启动：

控制研磨电机正转启动和反转启动。

⑧照明开关：
控制照明灯打开和关闭。
⑨停止开关：
按下停止按钮，控制机器停止前进或者停止后退。
⑩急停开关：

按下急停，遥控器显示急停ESTOP，所有开关输出断开，调速清零，所有操作无效；Release emergency stop，遥控器显示启动界面，调速恢复，照明恢复，其他开关依然断开，按下启动按钮进入操作界面，正反转输出恢复，调速恢复。
11 充电口：
Type-C充电口，不充电时，请盖紧防水盖，以免进水进灰。

12 电机调速：
研磨调速：旋转研磨旋钮，调节研磨速度，默认范围0-1500；
行走调速：旋转行走旋钮，调节行走速度，默认范围0.0-100；



Product installation steps

1.Install the receiver in the electric cabinet through the snap-on on the back，Or install it in the electrical cabinet through the screw holes at the four corners of the receiver.。
2.Refer to our receiver wiring diagram，Compare your on-site equipment，Connect the device to the receiver via wires。
3.After the receiver is fixed，The antenna equipped with the receiver must be connected，And install the outer end of the antenna or place it outside the electric cabinet，It is recommended to place the signal on the top of the electric cabinet.，It is not allowed to disconnect the antenna，Or place the antenna inside the electric cabinet，It may cause the signal to be unusable。
4.最后给遥控器充满电量，Then turn on the remote control power switch，The remote control display will show the normal working interface.，You can perform remote control operation。

Receiver installation size

Remote control parameter settings

Enter the remote control background parameter method：小电机速度调到0，Pull the forward rotation switch of the large motor upward 3 times in a row，Pull down 3 times in succession；
使用<Straight line correction>旋钮翻页，按下<start up>，转动<Straight line correction>旋钮修改参数，
After modification，Turn the page to the end，选择保存或不保存退出，按下<start up>退出菜单；
The parameters are as follows：
最小研磨速度：研磨电机初始速度，范围0-5000，默认0；
最小研磨电压：研磨电机初始输出电压，范围0-10，实际值为此值的1/2；默认0；
最大研磨速度：研磨电机最大速度值，范围0-5000，默认1500；
最大研磨电压：研磨电机最大输出电压，范围0-10，Default 10；实际输出为此值的1/2；
最小行走速度：行走电机初始速度，范围0-1000，默认0；
Remote control parameter settings
最小行走电压：行走电机初始输出电压，范围0-10，默认0；实际输出为此值的1/2；
最大行走速度：行走电机最大速度值，范围0-1000，Default 1000，对应屏幕显示100；
最大行走电压：行走电机最大输出电压，范围0-10，Default 10；实际输出为此值的1/2；
前后零位：摇杆前后方向中间零位设定，范围8-254，按住启动按钮，让摇杆自然居中，松开启动按钮，自动锁定零位值；
左右零位：摇杆左右方向中间零位设定，范围9-254，按住启动按钮，让摇杆自然居中，松开启动按钮，自动锁定零位值；

Frequency converter parameter setting

最大行走电压：行走电机最大输出电压，范围0-10，Default 10；实际输出为此值的1/2；
前后零位：摇杆前后方向中间零位设定，范围8-254，按住启动按钮，让摇杆自然居中，松开启动按钮，自动锁定零位值；
左右零位：摇杆左右方向中间零位设定，范围9-254，按住启动按钮，让摇杆自然居中，松开启动按钮，自动锁定零位值；
Remote control operating instructions
1.The machine is powered，Remote control turned on，按下<启动按钮>进入操作界面。
2.Enter the remote control background，Set the background parameters of the remote control，主要是设置行走和研磨电机变频器型号（机器厂家已设置的跳过这一步）。
3.设置好变频器的参数（机器厂家已设置的跳过这一步）。
4.扳动遥控器上的<illumination>开关，将照明灯打开。
5.调好研磨速度，扳动<正转>开关，启动研磨电机。
6.调好行走速度，扳动摇杆开关，控制机器前进或后退，以及转弯。

Fault situation Possible Cause Troubleshooting Methods
Press the power switch，
Cannot turn on and off，
The display does not light up
1.遥控器未安装电池或电池方向安装错误
2.Insufficient battery power
3.Remote control failure
1.Check the battery installation of the remote control
2.请充电
3.Contact the manufacturer to return to the factory for maintenance
Remote control turned on，
显示掉网重连
LostRF pls retry
1.The receiver is not powered
2.Receiver antenna not installed
3.The distance between the remote control and the machine is too far
4.Environmental interference
5.Before turning on the remote control，必须接收
器先通电，Turn on the remote control again
1.Check the receiver power on
2.Install the receiver antenna，Install the outer end of the antenna outside the electric cabinet to fix it
3.Operation at normal distance
4.① Optimize the wiring of the electric cabinet，The receiver antenna wiring should be kept away from 220V and
On line ② Try to use independent switching power supply to supply the receiver power supply as much as possible，and
Power cord adds power isolation module and magnetic ring，Increase anti-interference ability
Remote control turned on，
显示change battery
1.Insufficient battery power
2.Battery installation or poor contact
1.释放接收器上面的急停
2.检查急停开关是否故障，及时更换开关
Some buttons on the remote control
Or the switch does not respond
1.Switch damage failure
2.Receiver damage fault
1.Observe when flipping the switch，Is there a corresponding arrow on the display screen?；有箭
头显示，Indicates that the switch is normal；No arrow displayed means the switch is broken.，返
厂维修
2.Return to factory maintenance
After the receiver is powered on，
No light on the receiver
1.Power supply abnormality
2.Power wiring error
3.Receiver failure
1.Check if the power supply has voltage，Does the voltage meet the requirements
2.Check whether the positive and negative poles of the power supply are connected in reverse
3.Return to factory maintenance

1.Please at room temperature and pressure，Used in dry environments，Extend service life。
2.Please avoid getting wet in the rain、Used in abnormal environments such as blisters，Extend service life。
3.请注意充电口清洁，并在非充电时间将充电口盖子盖紧，以免进水进灰短路。
4.请避免遥控器被挤压和摔落，可能会导致遥控器损坏。
5.长时间不使用遥控器，请将遥控器存储在常温、干燥并且安全的地方。
6.Pay attention to moisture-proof and shock-proof during storage and transportation。

1.Please read the instructions for use in detail before use，Non-professional personnel are prohibited。
2.Please charge in time when the battery is too low，Avoid errors caused by insufficient battery power causing the remote control to be inoperable.。
4.If repair is required，Please contact the manufacturer，If damage caused by self-repair，The manufacturer will not provide a warranty。

(Remark：Product upgrade or upgrade situation，When purchasing products, please contact the sales staff for the latest product status)

]]> DH12S-2R-LD-485 crawler rope saw cutting remote control https://www.wixhc.com/cn/product/dh12s-2r-ld-485%e5%b1%a5%e5%b8%a6%e8%bd%a6%e7%bb%b3%e9%94%af%e5%88%87%e5%89%b2%e9%81%a5%e6%8e%a7%e5%99%a8 Wed, 25 Jun 2025 08:22:51 +0000 https://www.wixhc.com/cn/?post_type=product&p=117694

Crawler wire saw automatic cutting remote control is suitable for crawler wire saw cutting machines，Use 485Modbus RTU protocol to control the left and right crawler inverters，As well as large motor frequency conversion speed regulation start and front, rear, left and right direction controllers。And the working current of the large motor inverter can be read through the 485-Modbus RTU protocol，Analysis and comparison of large motor current at startup，Automatically adjust left and right track speeds in real time，Realize automatic cutting function。


1.Adopt 433MHZ wireless communication technology，Wireless operating distance 100 meters。
2.Adopt automatic frequency hopping function，Use 32 sets of wireless remote controls at the same time，No effect on each other。
3.Supports all frequency converters with 485-Modbus RTU protocol，The currently adapted inverter brands include： Shanghai Xielin、Fuji、Huichuan、Zhongchen、INVT、Yasukawa Tatsu。If the brand is not adapted, please contact us for customization.。
4.Support large motor inverter startup、speed regulation、Current reading。
5.Support left and right crawler inverter speed adjustment、start up、Front and rear left and right controls。
6.Support left and right crawler inverter linear correction，Keep the machine moving in a straight line。
7.Support wire saw automatic cutting function，According to the large motor current information，Automatically adjust left and right track speeds in real time。
8.It is also compatible with direct IO output to control motor start and stop.，Analog voltage output controls motor speed。




Comments： ①Screen display：

②Mode switch：
Adopt 2-speed switch，Can switch between automatic and manual modes，There will be corresponding mode display switching on the display screen.。
③ Enable：
Combination button，Some operations require pressing and holding the enable button to operate，See the description of each switch for details.。
④Large motor switch：
Adopt 3-speed reset switch，flip this switch，Can control forward and reverse rotation of large motors，The status will remain after letting go，There will be a corresponding display on the display，↑Arrow indicates forward rotation，↓Arrow indicates reversal。
⑤Small motor forward/reverse switch：
Adopt 3-speed self-locking switch，flip this switch，Can control the small motor to move forward and backward，There will be a corresponding display on the display，↑Arrow means moving forward，↓The arrow indicates going back。
⑥ Remote control power switch：
The large motor speed value changes by approximately 0.2 units， Using multi-turn encoder knob，Turn the knob，Adjust the large motor speed S1。1 frame per turn， Rapid rotation can quickly modify the large motor speed value。
⑦Small motor turning switch：
Adopt 3-speed reset switch，Turn this switch in manual mode，Can control small motor to turn left and right，The remote control will automatically stop this action after letting go.。 In forward state，flip this switch，There will be a corresponding display on the display，←Arrow indicates left turn，→The arrow indicates turning right。 In retreat state，flip this switch，There will be a corresponding display on the display，←Arrow indicates left turn，→The arrow indicates turning right。 Press and hold to enable，Then flip this switch，Can perform in-situ turning function，Turn faster。
⑧Speed ​​regulation of large motor ：
The large motor speed value changes by approximately 0.2 units， Using multi-turn encoder knob，Turn the knob，Adjust the large motor speed S1。1 frame per turn， Rapid rotation can quickly modify the large motor speed value。
⑨Small motor speed regulation：
(Linear deviation correction) adopts multi-turn encoder knob，In manual mode，Each time the knob is turned 1 step，The speed value of the small motor changes by about 0.1 unit，Quick rotation can quickly modify the speed value of the small motor。In automatic mode，Press enable button，Then rotate 1 frame each time，The small motor speed limit value F changes by about 0.1 unit，Quick rotation can quickly modify the speed limit value of small motors。Press enable button，Turn knob right，Straight line correction display:Df:left，Each turn of the knob increases by 1 unit.;Turn knob left，Straight line correction display:Df:right，Each turn of the knob increases by 1 unit.;Each correction unit corresponds to the motor speed regulation AVI voltage of about 0.02V.。


Product installation steps
1.Install the receiver in the electric cabinet through the snap-on on the back，Or install it in the electrical cabinet through the screw holes at the four corners of the receiver。
2.Refer to our receiver wiring diagram，Compare your on-site equipment，Connect the device to the receiver via wires。
3.After the receiver is fixed，The antenna equipped with the receiver must be connected，And install or place the outer end of the antenna outside the electrical cabinet，It is recommended to place the signal on the top of the electric cabinet.，It is not allowed to disconnect the antenna，Or place the antenna inside the electrical cabinet，This may result in poor signal and unusable。
4.Finally, install the batteries in the remote control，Tighten the battery cover，Then turn on the remote control power switch，The remote control display will show the normal working interface.，You can perform remote control operation。

Receiver installation size

Receiver Wiring Reference Diagram


Remote control parameter settings
Enter the remote control background parameter method：Move the mode switch to manual mode，Adjust the small motor speed to 25， or 0、10、20、40、50，Pull the forward rotation switch of the large motor upward 3 times in a row，Pull down 3 times in succession；
Use the "Small Motor Speed ​​Adjustment" knob to turn pages，After pressing enable, turn the small motor speed control knob to modify the parameters.； After modification，Turn the page to the end，Select Save and Exit，Press the enable button to exit the menu；
The parameters are as follows： Maximum current：Large motor current feedback value range，Setting range 15-200A，Default 60；
Speed ​​control parameters：Automatic mode small motor automatically accelerates speed，The smaller, the faster，Setting range 200-1500， Default 1000；
Deceleration parameters：Set the upper limit for allowed motor speed changes，When the current change exceeds this value，will slow down。 The smaller，The left and right motors decelerate faster，Range 05-12，Default 06；
Start self-locking： Acceleration a1：The larger the motor, the faster the speed increases.，Range 00-06，Default 01；
Deceleration a2：The larger the motor speed is, the faster it will decrease.，Range 00-06，Default 02；
Enable speed adjustment：Is it necessary to press Enable to adjust the speed of small motors?，00Disable，01enable，Default 01；
Will the large motor automatically maintain self-locking after the forward and reverse switch is released?，00do not maintain，01Keep，Default 01；
maximum walking：Maximum speed of left and right motors，Range 10-100，Default 50；
Cutting current：Maximum cutting current，The screen displays the IC value，Range 15-160，Default 30，Screen corresponding display IC：30。The upper limit of this parameter = maximum current x80%；
Default speed limit：The default small motor automatic cutting speed at startup，Range 00-100，Default 10，The screen should display F1.0，This parameter is only accurate when the maximum walk is set to 50。
wireless channel：Default 10，When the remote control signal is unstable，Or when there is signal interference on site，This parameter can be modified，switch channel，avoid distractions；
Speed ​​limit offset：Small motor automatic cutting speed upper limit，Range 00-200，Default 60，The screen corresponds to display 6.0；Display value upper limit = speed limit offset × 0.1；
largest host：Maximum speed of large motor，Range 10-100，Default 50；
mbus device (required)：Large motor inverter model selection，Range 00-03，Default 03；
00-Shanghai Xielin 01-Fuji
02-INVT 03-Huichuan (Zhongchen、Robin Kang)
sbus device (required)：Small motor inverter model selection，Range 00-05，Default 03；
00-Shanghai Xielin 01-Fuji
02-INVT 03-Huichuan (Zhongchen、Robin Kang)
04-Yasukawa Tatsu 05-None

Frequency converter parameter setting
1.Command source selection：Communication command channel
2.Main frequency source selection：communication given
3.baud rate：19200
4.Data format：No checksum，Data format<8-N-1>
5.Local address：Left frequency converter is set to 1，The right frequency converter is set to 2，Large motor inverter is set to 3

Remote control operating instructions
1.The machine is powered，Remote control turned on，Enter the remote control background，Set the background parameters of the remote control，The main thing is to set the inverter models of small motors and large motors (skip this step if the machine manufacturer has set it)；
2.Set the inverter parameters (skip this step if the machine manufacturer has set them)；
3.Switch the remote control to manual mode，Then use the remote control to move the machine to the working position；
4.In manual mode，Set the large motor cutting current setting value IC，Set the maximum motor speed；
5.Switch to automatic mode，Set the small motor cutting speed limit F value；
6.In automatic mode，Turn the big motor switch to forward to start the big motor，Then turn the small motor switch to forward or reverse gear，The remote control enters automatic cutting mode，Start cutting。




1.Please at room temperature and pressure，Used in dry environments，Extend service life。
2.Please avoid getting wet in the rain、Used in abnormal environments such as blisters，Extend service life。
3.Please keep the battery compartment and metal shrapnel area clean。
4.Please avoid squeezing and dropping the remote control, which may cause damage.。
5.Not used for a long time，Please remove the battery，And store the remote control and battery in a clean and safe place。
6.Pay attention to moisture-proof and shock-proof during storage and transportation。

1.Please read the instructions for use in detail before use，Non-professional personnel are prohibited。
2.Please replace the battery in time when the battery is too low，Avoid errors caused by insufficient battery power causing the remote control to be inoperable.。
3.If repair is required，Please contact the manufacturer，If damage caused by self-repair，The manufacturer will not provide a warranty。

(Remark：Product upgrade or upgrade situation，When purchasing products, please contact the sales staff for the latest product status)

]]> Track car rope saw cutting remote control DH22S-LD-485 https://www.wixhc.com/cn/product/%e5%b1%a5%e5%b8%a6%e8%bd%a6%e7%bb%b3%e9%94%af%e5%88%87%e5%89%b2%e9%81%a5%e6%8e%a7%e5%99%a8-dh22s-ld-485 Mon, 12 May 2025 05:15:57 +0000 https://www.wixhc.com/cn/?post_type=product&p=117676

1.Product introduction

Crawler wire saw automatic cutting remote control is suitable for crawler wire saw cutting machines，The 485Modbus RTU protocol is used to control the left and right crawler inverter speed regulation start and front, rear, left and right direction control.，And large motor frequency converter speed regulation start。And the working current of the large motor inverter can be read through the 485-Modbus RTU protocol，Analysis and comparison of large motor currents，Automatically adjust left and right track speeds in real time，Realize automatic cutting function。

 

2.Product features

1.Adopt 433MHZ wireless communication technology，Wireless operating distance 100 meters。

2.Adopt automatic frequency hopping function，Use 32 sets of wireless remote controls at the same time，No effect on each other。

3.Supports all frequency converters with 485 modbus RTU protocol，The currently adapted inverter brands include：Shanghai Xielin、Fuji、Huichuan、Zhongchen、INVT、Yasukawa Tatsu。If the brand is not adapted, please contact us for customization.。

4.Support large motor frequency converter speed regulation、start up、Current reading。

5.Support left and right crawler inverter speed adjustment、start up、Front and rear left and right controls。

6.Support left and right crawler inverter linear correction，Keep the machine moving in a straight line。

7.Support wire saw automatic cutting function，According to the large motor current information，Automatically adjust left and right track speeds in real time。

8.It is also compatible with direct IO output to control motor start and stop.，Analog voltage output controls motor speed。

3.product specifications

Handheld terminal working voltage and current 2AA battery-3V/10mA
Receiver operating voltage and current 24V/1A
Handheld transmit power 15dBm
Receiver Receive Sensitivity -100dBm
Wireless communication frequency 433Mhz frequency band
Operating temperature -25℃<X<55℃
Anti-fall height Comply with national testing standards
Waterproof level Ip67
Product size 225*84*58（mm）

 

4.Product function introduction

Comments：

①Screen display：

②Mode switch：

Adopt 2-speed switch，Can switch between automatic and manual modes，There will be a corresponding mode display switch on the display.。

③Enable：

Combination button，Some operations require pressing and holding the enable button to operate，See the description of each switch for details.。

④Large motor switch：

Adopt 3-speed reset switch，flip this switch，Can control forward and reverse rotation of large motors，The status will remain after letting go，There will be a corresponding display on the display，S1↑ arrow indicates forward rotation，S1↓ arrow indicates reversal。

⑤Small motor forward/reverse switch：

Adopt 3-speed self-locking switch，Press the enable button + flip the switch，Can control the small motor to move forward and backward，There will be a corresponding display on the display，↑↑Arrows indicate forward，↓↓The arrow indicates going back。

⑥Linear deviation correction：

Using multi-turn encoder knob，Press enable button，Turn knob right，Straight line correction display：Df：left，Each turn of the knob increases by 1 unit.，The left motor speed increases by 0.1 units；Turn knob left，Straight line correction display：Df：right，Each turn of the knob increases by 1 unit.，The right motor speed increases by 0.1 units。

⑦Small motor turning switch：

Adopt 3-speed reset switch，Turn this switch in manual mode，Can control small motor to turn left and right，The remote control will automatically stop this action after letting go.。In forward state，flip this switch，There will be a corresponding display on the display，←↑ arrow indicates left turn，↑→arrow indicates turning right。In retreat state，flip this switch，There will be a corresponding display on the display，←↓ arrow indicates left turn，↓→arrow indicates turning right。

⑧Speed ​​regulation of large motor：

Using multi-turn encoder knob，Rotate 1 frame each time，The large motor speed value changes by approximately 0.2 units，Rapid rotation can quickly modify the large motor speed value。

⑨Small motor speed regulation：

Using multi-turn encoder knob，In manual mode，Press enable button，Then rotate 1 frame each time，The speed value of the left and right small motors changes by about 0.1 unit，Quick rotation can quickly modify the speed value of the small motor。In automatic mode，Press enable button，Then rotate 1 frame each time，The small motor speed limit value F changes by about 0.1 unit，Quick rotation can quickly modify the speed limit value of small motors。

⑩Remote control power switch：

Remote control display power on。

 

5.Product accessories diagram

 

6.Product Installation Guide
6.1Product installation steps

1.Install the receiver in the electric cabinet through the snap-on on the back，Or install it in the electrical cabinet through the screw holes at the four corners of the receiver.。

2.Refer to our receiver wiring diagram，Compare your on-site equipment，Connect the device to the receiver via wires。

3.After the receiver is fixed，The antenna equipped with the receiver must be connected，And install the outer end of the antenna or place it outside the electric cabinet，It is recommended to place the signal on the top of the electric cabinet.，It is not allowed to disconnect the antenna，or will

The antenna is placed inside the electrical cabinet，It may cause the signal to be unusable。

4.Finally, install the batteries in the remote control，Tighten the battery cover，Then turn on the remote control power switch，The remote control display will show the normal working interface.，You can perform remote control operation。

6.2Receiver installation size

6.3Receiver Wiring Reference Diagram

7.Product operating instructions

7.1Remote control parameter settings
Enter the remote control background parameter method：Move the mode switch to manual mode，The speed of the small motor is adjusted to 25 on the left and right，Or both are 0、10、20、40、50，Pull the forward rotation switch of the large motor upward 3 times in a row，Pull down 3 times in succession；
Use the "Small Motor Speed ​​Adjustment" knob to turn pages，After pressing enable, turn the small motor speed control knob to modify the parameters.；
After modification，Turn the page to the end，Select Save and Exit，Press the enable button to exit the menu；
The parameters are as follows：
Maximum current：Large motor current feedback value range，Setting range 15-200A，Default 100；
Speed ​​regulation parameters：Automatic mode small motor automatically accelerates speed，The smaller, the faster，Setting range 200-1500，Default 800；
Deceleration parameters：Set the upper limit for allowed motor speed changes，When the current change exceeds this value，will slow down。
The smaller，The left and right motors decelerate faster，Range 05-12，Default 06；
Acceleration a1：The larger the motor, the faster the speed increases.，Range 00-06，Default 01；

Deceleration a2：The larger the motor speed is, the faster it will decrease.，Range 00-06，Default 02；

Enable speed adjustment：Is it necessary to press Enable to adjust the speed of small motors?，00Disable，01enable，Default 01；
Start self-locking：Will the large motor automatically maintain self-locking after the forward and reverse switch is released?，00do not maintain，01Keep，Default 01；
Maximum walking：Maximum speed of left and right motors，Range 10-100，Default 50；
Cutting current：Maximum cutting current，The screen displays the IC value，Range 15-160，Default 30，Screen corresponding display IC：30。The upper limit of this parameter = maximum current x80%；
Default speed limit：The default small motor automatic cutting speed at startup，Range 00-100，Default 10，The screen correspondingly displays F1.0，This parameter is only accurate when the maximum walk is set to 50。
Automatic mode：Set to 00，Auto/manual switch is a mode switch，Set to 01，Turn the automatic/manual switch to the automatic position，Display display lighting，Automatic terminal output closure on receiver，Hit manual，Automatic output terminal disconnection；
Speed ​​limit offset：Small motor automatic cutting speed upper limit，Range 00-200，Default 60，The screen corresponds to display 6.0；Display value upper limit = speed limit offset × 0.1；
Maximum host：Maximum speed of large motor，Range 10-100，Default 50；
mbus device (required)：Large motor inverter model selection，Range 00-03，Default 03；
00-Shanghai Xielin 01-Fuji
02-INVT 03-Huichuan (Zhongchen、Robin Kang)
sbus device (required)：Small motor inverter model selection，Range 00-05，Default 03；
00-Shanghai Xielin 01-Fuji
02-INVT 03-Huichuan (Zhongchen、Robin Kang)
04-Yaskawa Da 05-None

7.2Frequency converter parameter setting

1.Command source selection：Communication command channel

2.Main frequency source selection：communication given

3.baud rate：19200

4.Data format：No checksum，Data format<8-N-1>

5.Local address：Left frequency converter is set to 1，The right frequency converter is set to 2，Large motor inverter is set to 3

 

7.3Remote control operating instructions

1.The machine is powered，Remote control turned on，Enter the remote control background，Set the background parameters of the remote control，main

It is to set the inverter models of small motors and large motors (skip this step if the machine manufacturer has set it)；

2.Set the inverter parameters (skip this step if the machine manufacturer has set them)；

3.Switch the remote control to manual mode，Then use the remote control to move the machine to the working position；

4.In manual mode，Set the large motor cutting current setting value IC，Set the maximum motor speed；

5.Switch to automatic mode，Set the small motor cutting speed limit F value；

6.In automatic mode，Turn the big motor switch to forward to start the big motor，Then turn the small motor switch to

Forward or reverse gear，The remote control enters automatic cutting mode，Start cutting。

 

8.Product troubleshooting

Fault situation Possible Cause
Troubleshooting Methods
Press the power switch，
Cannot turn on and off，
The display does not light up
1.The battery is not installed on the remote control
Or the battery direction is installed incorrectly
2.Insufficient battery power
3.Remote control failure
1.Check the battery installation of the remote control
2.Replacement battery
3.Contact the manufacturer to return to the factory for maintenance
Remote control turned on，
Shows network outage and emergency stop!
Please try again!
1.The receiver is not powered
2.Receiver antenna not installed
3.The distance between the remote control and the machine is too far
4.Environmental interference
5.Before turning on the remote control，The receiver must be powered on first，Turn on the remote control again
1.Check the receiver power on
2.Install the receiver antenna，Install the outer end of the antenna outside the electric cabinet to fix it
3.Operation at normal distance
4.① Optimize the wiring of the electric cabinet，Keep the receiver antenna wiring as far away as possible from 220V and above lines. ② Try to use an independent switching power supply for the receiver power supply.，And add power isolation module and magnetic ring to the power cord.，Increase anti-interference ability
Remote control turned on，show chage battery
1.Insufficient battery power
2.Battery installation or poor contact
1.Replacement battery
2.Check battery installation，And whether the metal sheets at both ends of the battery compartment are clean and free of foreign matter，Clean it
Some buttons on the remote control
Or the switch does not respond
1.Switch damage failure
2.Receiver damage fault
1.Observe when flipping the switch，Is there a corresponding arrow on the display screen?；There is an arrow displayed，Indicates that the switch is normal；No arrow displayed means the switch is broken.，Return to factory maintenance
2.Return to factory maintenance
After the receiver is powered on，No light on the receiver
1.Power supply abnormality
2.Power wiring error
3.Receiver failure
1.Check if the power supply has voltage，Does the voltage meet the requirements
2.Check whether the positive and negative poles of the power supply are connected in reverse
3.Return to factory maintenance

 

9.Maintenance and care

1.Please at room temperature and pressure，Used in dry environments，Extend service life。

2.Please avoid getting wet in the rain、Used in abnormal environments such as blisters，Extend service life。

3.Please keep the battery compartment and metal shrapnel area clean。

4.Please avoid squeezing and dropping the remote control, which may cause damage.。

5.Not used for a long time，Please remove the battery，And store the remote control and battery in a clean and safe place。

6.Pay attention to moisture-proof and shock-proof during storage and transportation。

10.safety information

1.Please read the instructions for use in detail before use，Non-professional personnel are prohibited。

2.Please replace the battery in time when the battery is too low，Avoid errors caused by insufficient battery power causing the remote control to be inoperable.。

4.If repair is required，Please contact the manufacturer，If damage caused by self-repair，The manufacturer will not provide a warranty。

]]> Industrial wireless remote control DH01R-4W-26K https://www.wixhc.com/cn/product/dh01r-4w-26k Fri, 05 Jan 2024 02:12:41 +0000 https://www.wixhc.com/cn/?post_type=product&p=100844

model：DH01R-4W-26K adapter equipment：Various industrial equipment

Remark：Three types of antennas can be selected，The default suction cup antenna is equipped with standard

Remark：
① DH01R series，If the suffix is ​​T, it means an emergency stop output；Without T means without emergency stop output。
②If there is no analog output，No need to note 0W or 0R；Analog quantity W1, W2, W3, W4 defaults to 0-10V analog voltage output；At the same time, W1 and W2 can expand the output of 2 isolated digital potentiometers，Range 0-5K ohms，1/2watt；Resolution：20ohm。These two digital potentials can be used as welding current and welding voltage control of the welding machine。If this digital potentiometer output is required，User notes are required。
④Analog input，Range from 1 to 2，Indicates that there are 1 to 2 analog inputs (maximum 2 channels)；When there is an analog input，Need to note the voltage range of the analog input (our receiver defaults to 0-5V，Users can also note that it is 4-20 mA or 0-10V, etc.) and the display range corresponding to the analog quantity.(for example：Shows 0-100 volts or 0-1000 amps)
The two analog quantities can be used as display of welding current and welding voltage。

W1 knob value：W1：0-1000(Parameters can be adjusted 0-9999)
W2 knob value：W2：0-5000(Parameters can be adjusted 0-9999)
W3 knob value：W3：0-5000(Parameters can be adjusted 0-9999)
W4 knob value：W4：0-5000(Parameters can be adjusted 0-9999)
ADC1 feedback display：0-1000(Parameters can be adjusted 0-5000)
ADC2 feedback display：0-1000(Parameters can be adjusted 0-5000)

Low pressure：The battery of the remote control is too low，Please replace the battery

Fall out of the internet：Wireless signal interruption，Please check the receiver power supply，Power on again，Restart the remote control

1、Remote control turned on
The receiver is powered on，The receiver operating indicator flashes；Two No. 5 batteries installed on the remote control，Turn on the power switch，Display value，It means the startup is successful。The receiver operating indicator light becomes constant。

2、Switch and button functions
Operate twist switches and buttons on the remote control arbitrarily，It can control the corresponding switch signal output point at the receiver end，All switch signal output points on the receiver are normally open by default

3、W1-W4 speed regulation
Rotate the knob in W1-W4 arbitrarily，Can operate the analog output signal or potentiometer signal corresponding to the receiver end，
The analog output signal at the receiver end is a 0-10V voltage signal by default.，Potentiometer signal default 0-5K；

4、Emergency stop function
Take the emergency stop button，All switch signal outputs are disconnected，Analog output is disconnected；After the emergency stop is released，All switch signal recovery，Analog output recovery；
After the remote control is turned off for 5 seconds，All switch signal outputs are disconnected，The simulation remains unchanged，Remote control turned on，Automatically restore the switch signal output；

5、Parameter menu (user prohibits private modification)
Some functions of the remote control can be adjusted through parameters，When the display screen W1=0，Tap the K9-B button 3 times in a row，Then click the K9-A button 3 times in a row，Enter the parameter menu；
K9-A and K9-B keys to turn the menu page and select parameters；Hold K1-A，Press the K9-A/B button again，Make parameter modifications；
Exit the Parameters Menu：Choose to save or not，Then press the K1-A button to confirm the exit；
F1W1 range:Display range value of display W1 knob，0-9999Adjustable；
F2W2 range:Display range value of W2 knob on display screen，0-9999Adjustable；
F3W3 range:Display range value of W3 knob on display screen，0-9999Adjustable；
F4W4 range:Display range value of W4 knob on display screen，0-9999Adjustable；
F5A1 range:Display ADC1 feedback display range value，0-5000Adjustable；
F6A2 range:Display ADC2 feedback display range value，0-5000Adjustable；
Alarm current：Set the alarm value displayed by ADC1 and ADC2 feedback，When ADC1 and 2 exceed this value，Remote control display alarm prompt；When this value is 0，Alarm function invalid；

 

The final right to interpret this product belongs to Chengdu Xinshen Technology Co., Ltd.。

]]> Floor grinder wireless remote control DH22ST-Le https://www.wixhc.com/cn/product/dh22st-le Thu, 28 Dec 2023 05:26:11 +0000 https://www.wixhc.com/cn/?post_type=product&p=100263

model：DH22ST-Le

Adaptive equipment：Floor grinder

Remark：Three types of antennas can be selected，The default suction cup antenna is equipped with standard

emergency stop：The emergency stop button was photographed，Please release the emergency stop button

Low pressure：The battery of the remote control is too low，Please replace the battery

Fall out of the internet：Wireless signal interruption，Please check the receiver power supply，Power on again，Restart the remote control

1、Remote control turned on
The receiver is powered on，The RF-LED light on the receiver starts to flash；Two No. 5 batteries installed on the remote control，Turn on the power switch，Display display motor speed，It means the startup is successful。
2、illumination

Click the "Lighting" button，Receiver lighting output is on，A lighting icon appears on the display

Click the Light button again，Receiver lighting output is off，Photo icon disappears from display。

3、Grinding motor and speed regulation
Turn the "Forward/Reverse" switch to forward，Receiver grind forward turn open，The display displays forward rotation
Turn the "Forward/Reverse" switch to reverse，Receiver Grind Reversal Open，Display display inversion

Turn the "Grinding Speed" knob，You can adjust the receiver grinding speed output voltage 0-10V；

4、Travel motor and speed regulation
Turn the "Forward/Reverse" switch to forward，Receiver Revolver Progress and Right Progress Open，Display forward

Turn the "Forward/Reverse" switch to the back，Receiver reversal and right wheel reversal open，Display back

Turn the "walking speed adjustment" knob，You can adjust the speed output voltage of the left and right wheels of the receiver from 0-10V.；
5、Turn left and right

Turn the "Left/Right" switch to the left，Receiver right wheel advances to open，The display display turns left

Turn the "Left/Right" switch to the right，Receiver revolver advance opens，The display display turns right
6、Turning in place
Turn left in place：Press and hold the Enable button，Move the "turn left/right" switch to the left turn position，Receiver left wheel reverse and right wheel forward open，Start turning left in place；
Turn right in place：Press and hold the Enable button，Move the "turn left/right" switch to the right turn position，Receiver left wheel forward and right wheel reverse open，Start turning right in place；
7、emergency stop

Take the emergency stop button，Receiver emergency stop output is disconnected；All switches are off，All speeds cleared；

8、Straight line correction
When the left and right motor is moving forward and backward，There is a difference in the left and right speeds，Straight-line walking is offset，The linear deviation correction function of the remote control can be used，Fine-tune the speed of left and right wheels；
Principle of correction：Through bias correction function，Fine-tune revolver speed，To achieve the same speed as the right wheel，Realize the synchronization of left and right wheel speeds，Eliminate offsets；
Correction operation method：Press and hold the Enable button，Slowly turn the "Linear Correction" knob；
Rotate clockwise，Increase the revolver speed voltage，Increased deviation correction value of the display screen；
Rotate counterclockwise，Reduce the revolver speed voltage，The display deviation correction value is reduced；

Correction range：Correction value -90 to 90；1The correction voltage of a correction unit is about 0.04V；

9、Parameter menu (user prohibits private modification)
Enter parameter menu mode：When grinding is 0，Forward/reverse rotation 3 times in a row，Break it off 3 more times；
Exit method：Choose to save or not save，Press the enable button to confirm；
Linear fine adjustment range：0-120；
Grinding speed：0-3000；
walking speed：0-1000；

Receiver operating power supply
DC24V/1A (independent power supply)
Receiver output point load AC0-250V/3A DC0-30V/5A
Receiver speed regulation output voltage DC0-10V

The final right to interpret this product belongs to Chengdu Xinshen Technology Co., Ltd.。

]]> Automatic cutting wireless remote control of wire saw machine DH12S-P6S https://www.wixhc.com/cn/product/%e7%bb%b3%e9%94%af%e6%9c%ba%e8%87%aa%e5%8a%a8%e5%88%87%e5%89%b2%e6%97%a0%e7%ba%bf%e9%81%a5%e6%8e%a7%e5%99%a8-dh12s-p6s Fri, 01 Dec 2023 03:09:23 +0000 https://www.wixhc.com/cn/?post_type=product&p=98272


model：DH12S-P6S adapter equipment：Wire saw/blade saw machine

Remark：Three types of antennas can be selected，The default suction cup antenna is equipped with standard

Main motor speed：host：0-50
Travel motor speed：OK：0-50
Automatic cutting travel motor maximum speed limit：speed：0-30(The parameters are adjustable)
Automatic cutting main motor set current：set up：28(The parameters are adjustable)
Swing arm motor speed：put：0-50

Low pressure：The battery of the remote control is too low，Please replace the battery

Fall out of the internet：Wireless signal interruption，Please check the receiver power supply，Power on again，Restart the remote control

1、Remote control turned on
The receiver is powered on，The D2 power supply light on the receiver is always on，D1 signal light starts to flash；Two No. 5 batteries installed on the remote control，Turn on the power switch，Display display motor speed，It means the startup is successful。
2、Main motor and speed regulation
Press and hold "Speed ​​control enable"，Turn the "Forward/Reverse" switch to forward，The main motor of the receiver rotates forward and turns on；
Press and hold "Speed ​​control enable"，Turn the "Forward/Reverse" switch to reverse，Receiver main motor reverses and turns on；

Simply move the switch to the middle or reverse，The main motor stops immediately，No need to press speed control to enable；

Turn the "Big Motor" knob，The speed regulation voltage of the receiver main motor inverter can be adjusted 0-10V；
3、Walking motor
Press and hold "Speed ​​control enable"，Turn the "Forward/Reverse" switch to forward or backward，The walking motor will move at a high speed of 50；
4、Swing arm motor and speed regulation
Turn the "Swing Arm/Return" switch to the swing arm or back，The swing arm motor of the receiver starts；Then turn the "speed adjustment" knob，Can adjust the speed of the swing arm motor；
Press and hold "Speed ​​control enable"，Then flip the "swing arm/reverse" switch，The swing arm motor will move at a high speed of 50；
5、Travel motor speed limit adjustment
Press and hold the "Speed ​​Enable" button，Turn "Speed ​​Adjustment" to adjust the maximum speed limit of the traveling motor during automatic cutting.；
6、Automatic cutting

first step，Start the main motor；Step 2，Adjust the maximum speed limit of the traveling motor；Step 3，Turn the "forward/reverse" switch to move forward or backward，Enter automatic cutting mode；

7、Parameter settings (users prohibit private modification)
Enter the parameter menu：In manual mode，When the main motor speed is 0，Forward/reverse switch is bent up 3 times in a row，Then break it 3 times in a row，Enter the parameter menu；
Exit the Parameters Menu：Speed ​​adjustment knob page turn，Choose to save or not save，Press the enable button to confirm；
Rated current:Maximum value of main motor current，Unit Ampere；
Speed ​​regulation parameters:Automatic cutting control parameters，Default 800，Unit milliseconds，Modification is prohibited；
Deceleration parameters:When the cutting current change value exceeds this value，Start to decelerate rapidly，Unit Ampere；
Acceleration a1:When the cutting current is lower than the set cutting current，The speed value of each acceleration of the walking motor；
Deceleration a2: When the cutting current is higher than the set cutting current，The speed value of the walking motor reduces each time it decelerates；
Swing arm current:default value，Modification is prohibited；
Stop time:After shutdown due to current overload in automatic mode，Check the current again after a period of time，If it is less than the set current，Automatically start the walking motor；Unit second，default value，Modification is prohibited；
Maximum current:Main motor feedback current range，Unit Ampere；
Maximum host:Remote control main motor speed display range；
Maximum walking:Invalid parameter；
Speed ​​limit offset:When cutting automatically,Remote control display walking motor speed limit = 50% of this parameter；
Add sensitivity:When the feedback current of the main motor increases，The value increased each time exceeds this value，Walking motor acceleration；
Reduce sensitivity:Main motor feedback current decreases，The value reduced each time exceeds this value，Walking motor slows down；
Sensitivity offset:The offset increase of the adding and subtracting sensitivity parameters；
Set current:Automatic cutting，The threshold for feedback current of main motor，More than this value，The walking motor starts to slow down；Below this value，The walking motor starts to accelerate；Unit Ampere；
Empty exit:When automatic mode starts，If the main motor feedback current is less than this value，is in idling mode，greater than this value，then exit idling mode，Enter cutting mode，Unit Ampere；
No-load current:When automatic mode starts，If the main motor feedback current is less than this value，is in no-load mode，greater than this value，then exit the no-load mode，Enter cutting mode，Unit Ampere；
Swing arm speed:Swing arm motor startup speed；
cutting mode:Switch between blade saw and wire saw modes，After switching, the parameters will also switch accordingly.；In blade saw mode，A swing arm motor is added to the remote control display，The wire saw mode does not have a swing arm motor.；
Debounce time:When the main motor feedback current exceeds the stop current，Will continuously detect the feedback current，The debounce time is the duration of this continuous detection.，exceed this time，Detect that the main motor current still exceeds the stop current，walkThe motor will stop；Otherwise, the walking motor will continue to move forward；
stop current:The feedback current of the main motor exceeds this value，The walking motor will stop；Unit Ampere；
Offset default:The initial value of the speed limit of the traveling motor when the remote control is turned on = 50% of this value；

 

Receiver operating power supply
DC24V/1A (independent power supply)
Receiver output point load AC0-250V/3A DC0-30V/5A
Receiver speed regulation output voltage DC0-10V

The final right to interpret this product belongs to Chengdu Xinshen Technology Co., Ltd.。

 

]]> Crawler rope saw machine-automatic wireless remote control DH12S-LD https://www.wixhc.com/cn/product/%e5%b1%a5%e5%b8%a6%e7%bb%b3%e9%94%af%e6%9c%ba-%e8%87%aa%e5%8a%a8%e6%97%a0%e7%ba%bf%e9%81%a5%e6%8e%a7%e5%99%a8-dh12s-ld Fri, 17 Nov 2023 05:53:18 +0000 https://www.wixhc.com/cn/?post_type=product&p=97249

model：DH12S-LD Adaptive equipment：Crawler rope sawing machine

Remark：Three types of antennas can be selected，The default suction cup antenna is equipped with standard

Large motor speed：S1：0-50
Small motor speed：S2：0-50
Automatic cutting motor maximum speed limit：F：0-30(The parameters are adjustable)
Automatic cutting maximum current：Ic：0-35(The parameters are adjustable)
Linear deviation correction value：Df：-99-99(1 unit is approximately 0.02V)

Low pressure：The battery of the remote control is too low，Please replace the battery

Fall out of the internet：Wireless signal interruption，Please check the receiver power supply，Power on again，Restart the remote control

1、Remote control turned on

The receiver is powered on，The RF-LED light on the receiver starts to flash；Two No. 5 batteries installed on the remote control，Turn on the power switch，Display display motor speed，It means the startup is successful。

2、Large motor and speed regulation
Turn the "Forward/Reverse" switch to forward，The receiver's large motor turns on，The display displays forward rotation；
Turn the "Forward/Reverse" switch to reverse，Receiver large motor reversal on，Display display inversion；

Rotate the "Large Motor Speed ​​Regulation" knob，It can adjust the output voltage of the receiver large motor speed regulation 0-10V；

3、Small motor and speed regulation

Turn the "Forward/Reverse" switch to forward，Receiver Revolver Progress and Right Progress Open，Display forward

Turn the "Forward/Reverse" switch to the back，Receiver reversal and right wheel reversal open，Display back
In manual mode：Rotate the "Small Motor Speed ​​Regulation" knob，At the same time, adjust the output voltage of the receiver's left wheel right wheel speed regulation 0-10V；

4、Turn left and right

Turn the "Left/Right" switch to the left，Receiver right wheel advances to open，The display display turns left

Turn the "Left/Right" switch to the right，Receiver revolver advance opens，The display display turns right
5、Turning in place
In manual mode：
Turn left in place：Press and hold the Enable button，Turn the "Left/Right" switch to the left，Receiver's reversal and right wheel advance open，Start turning left in place；

Turn right in place：Press and hold the Enable button，Turn the "Left/Right" switch to the right，The receptacle's revolver advances and the right-wheel backs opens，Start turning right in place；

6、Small motor speed limit adjustment

In automatic mode：Press and hold the Enable button，Rotate the "Small Motor Speed ​​Regulation" to adjust the maximum speed of the small motor during automatic cutting；

7、Automatic cutting
first step，Start the large motor；
Step 2，Switch the mode switch to "auto"；
Step 3，Start the small motor，The screen display enters "Cutting Automatic"，Indicates that the automatic cutting mode has been entered；

 

8、Straight line correction
When the left and right motor is moving forward and backward，There is a difference in the left and right speeds，Straight-line walking is offset，The linear deviation correction function of the remote control can be used，Fine-tune the speed of left and right wheels；
Principle of correction：Through bias correction function，Fine-tune revolver speed，To achieve the same speed as the right wheel，Realize the synchronization of left and right wheel speeds，Eliminate offsets；
Correction operation method：In manual mode，Press and hold the Enable button，Rotate "small motor speed regulation"；
Rotate clockwise，Increase the revolver speed voltage，Increased deviation correction value of the display screen；
Rotate counterclockwise，Reduce the revolver speed voltage，The display deviation correction value is reduced；

Correction range：Correction value -90 to 90；1The bias correction voltage of each deviation correction unit is approximately 0.02V；

9、Parameter menu (user prohibits private modification)
Some functions of the remote control can be adjusted through parameters，In manual mode，When the speed of small motor S2 is 10，
Forward/reverse switch is bent up 3 times in a row，Then break it 3 times in a row，Enter the parameter menu；
Exit the Parameters Menu：Choose to save or not，Then press the enable button to confirm exit；
Maximum current:Working current of the cutting motor，The cutting current is 80% of this current；
Speed ​​regulation parameters:Automatic cutting control parameters，Default 800，Modification is prohibited；
Deceleration parameters:Automatic cutting control parameters，When the cutting current change value exceeds this value，Start slowing down
Acceleration a1: Automatic cutting control parameters，When the cutting current is lower than the set cutting current，Speed ​​up slowly；
Deceleration a2: Automatic cutting control parameters，When the cutting current is higher than the set cutting current，Slow speed；
Automatic knife collection:invalid；
Start self-locking：0，Don't lock yourself；1，Self-locking. Press the enable key + forward and reverse to take effect，And lock it；
Maximum walking:Minimum motor speed；
Cutting current:Set the maximum current value of the main motor for automatic cutting，The feedback current exceeds this value，Start slowing down；
Default speed limit:When powering on，Default maximum speed for automatic cutting speed；
Automatic mode:0，Automatic switch is automatic control；1，Automatic switch control automatic IO output point；
Speed ​​limit offset:When cutting automatically,Maximum speed of small motor；
Maximum host:大电机最大速度.

 

Receiver operating power supply DC24V/1A (independent power supply)
Receiver output point load AC0-250V/3A DC0-30V/5A
Receiver speed regulation output voltage
DC0-10V
]]> Multi-switch industrial wireless remote control DH05 https://www.wixhc.com/cn/product/%e5%a4%9a%e5%bc%80%e5%85%b3%e9%87%8f%e5%b7%a5%e4%b8%9a%e6%97%a0%e7%ba%bf%e9%81%a5%e6%8e%a7%e5%99%a8dh05 Fri, 22 Apr 2022 07:25:30 +0000 https://www.wixhc.com/cn/?post_type=product&p=55904

]]> Floor grinder industrial automation control remote control DH22-2R-7K https://www.wixhc.com/cn/product/%e5%9c%b0%e5%9d%aa%e7%a0%94%e7%a3%a8%e6%9c%ba%e5%b7%a5%e4%b8%9a%e8%87%aa%e5%8a%a8%e5%8c%96%e6%8e%a7%e5%88%b6%e9%81%a5%e6%8e%a7%e5%99%a8dh22-2r-7k Tue, 19 Apr 2022 01:33:16 +0000 https://www.wixhc.com/cn/?post_type=product&p=55671

]]> Roller frame, wire saw cutting, multi-function wireless industrial remote control, DH22 https://www.wixhc.com/cn/product/%e6%bb%9a%e8%bd%ae%e6%9e%b6-%e7%bb%b3%e9%94%af%e5%88%87%e5%89%b2-%e5%a4%9a%e5%8a%9f%e8%83%bd%e6%97%a0%e7%ba%bf%e5%b7%a5%e4%b8%9a%e9%81%a5%e6%8e%a7%e5%99%a8-dh22 Fri, 18 Mar 2022 07:56:15 +0000 https://www.wixhc.com/cn/?post_type=product&p=53346

]]>