Automatic cutting wireless remote control – Core Synthesis Technology

Industrial wireless remote control DH01R-4W-26K

xinhecheng — Fri, 05 Jan 2024 02:12:41 +0000

model：DH01R-4W-26K adapter equipment：Various industrial equipment

Remark：Three types of antennas can be selected，The default suction cup antenna is equipped with standard

Remark：
① DH01R series，If the suffix is T, it means an emergency stop output；Without T means without emergency stop output。
②If there is no analog output，No need to note 0W or 0R；Analog quantity W1, W2, W3, W4 defaults to 0-10V analog voltage output；At the same time, W1 and W2 can expand the output of 2 isolated digital potentiometers，Range 0-5K ohms，1/2watt；Resolution：20ohm。These two digital potentials can be used as welding current and welding voltage control of the welding machine。If this digital potentiometer output is required，User notes are required。
④Analog input，Range from 1 to 2，Indicates that there are 1 to 2 analog inputs (maximum 2 channels)；When there is an analog input，Need to note the voltage range of the analog input (our receiver defaults to 0-5V，Users can also note that it is 4-20 mA or 0-10V, etc.) and the display range corresponding to the analog quantity.(for example：Shows 0-100 volts or 0-1000 amps)
The two analog quantities can be used as display of welding current and welding voltage。

W1 knob value：W1：0-1000(Parameters can be adjusted 0-9999)
W2 knob value：W2：0-5000(Parameters can be adjusted 0-9999)
W3 knob value：W3：0-5000(Parameters can be adjusted 0-9999)
W4 knob value：W4：0-5000(Parameters can be adjusted 0-9999)
ADC1 feedback display：0-1000(Parameters can be adjusted 0-5000)
ADC2 feedback display：0-1000(Parameters can be adjusted 0-5000)

Low pressure：The battery of the remote control is too low，Please replace the battery

Fall out of the internet：Wireless signal interruption，Please check the receiver power supply，Power on again，Restart the remote control

1、Remote control turned on
The receiver is powered on，The receiver operating indicator flashes；Two No. 5 batteries installed on the remote control，Turn on the power switch，Display value，It means the startup is successful。The receiver operating indicator light becomes constant。

2、Switch and button functions
Operate twist switches and buttons on the remote control arbitrarily，It can control the corresponding switch signal output point at the receiver end，All switch signal output points on the receiver are normally open by default

3、W1-W4 speed regulation
Rotate the knob in W1-W4 arbitrarily，Can operate the analog output signal or potentiometer signal corresponding to the receiver end，
The analog output signal at the receiver end is a 0-10V voltage signal by default.，Potentiometer signal default 0-5K；

4、Emergency stop function
Take the emergency stop button，All switch signal outputs are disconnected，Analog output is disconnected；After the emergency stop is released，All switch signal recovery，Analog output recovery；
After the remote control is turned off for 5 seconds，All switch signal outputs are disconnected，The simulation remains unchanged，Remote control turned on，Automatically restore the switch signal output；

5、Parameter menu (user prohibits private modification)
Some functions of the remote control can be adjusted through parameters，When the display screen W1=0，Tap the K9-B button 3 times in a row，Then click the K9-A button 3 times in a row，Enter the parameter menu；
K9-A and K9-B keys to turn the menu page and select parameters；Hold K1-A，Press the K9-A/B button again，Make parameter modifications；
Exit the Parameters Menu：Choose to save or not，Then press the K1-A button to confirm the exit；
F1W1 range:Display range value of display W1 knob，0-9999Adjustable；
F2W2 range:Display range value of W2 knob on display screen，0-9999Adjustable；
F3W3 range:Display range value of W3 knob on display screen，0-9999Adjustable；
F4W4 range:Display range value of W4 knob on display screen，0-9999Adjustable；
F5A1 range:Display ADC1 feedback display range value，0-5000Adjustable；
F6A2 range:Display ADC2 feedback display range value，0-5000Adjustable；
Alarm current：Set the alarm value displayed by ADC1 and ADC2 feedback，When ADC1 and 2 exceed this value，Remote control display alarm prompt；When this value is 0，Alarm function invalid；

The final right to interpret this product belongs to Chengdu Xinshen Technology Co., Ltd.。

Floor grinder wireless remote control DH22ST-Le

xinhecheng — Thu, 28 Dec 2023 05:26:11 +0000

model：DH22ST-Le

Adaptive equipment：Floor grinder

Remark：Three types of antennas can be selected，The default suction cup antenna is equipped with standard

emergency stop：The emergency stop button was photographed，Please release the emergency stop button

Low pressure：The battery of the remote control is too low，Please replace the battery

Fall out of the internet：Wireless signal interruption，Please check the receiver power supply，Power on again，Restart the remote control

1、Remote control turned on

The receiver is powered on，The RF-LED light on the receiver starts to flash；Two No. 5 batteries installed on the remote control，Turn on the power switch，Display display motor speed，It means the startup is successful。

2、illumination

Click the "Lighting" button，Receiver lighting output is on，A lighting icon appears on the display

Click the Light button again，Receiver lighting output is off，Photo icon disappears from display。

3、Grinding motor and speed regulation

Turn the "Forward/Reverse" switch to forward，Receiver grind forward turn open，The display displays forward rotation
Turn the "Forward/Reverse" switch to reverse，Receiver Grind Reversal Open，Display display inversion

Turn the "Grinding Speed" knob，You can adjust the receiver grinding speed output voltage 0-10V；

4、Travel motor and speed regulation

Turn the "Forward/Reverse" switch to forward，Receiver Revolver Progress and Right Progress Open，Display forward

Turn the "Forward/Reverse" switch to the back，Receiver reversal and right wheel reversal open，Display back

Turn the "walking speed adjustment" knob，You can adjust the speed output voltage of the left and right wheels of the receiver from 0-10V.；

5、Turn left and right

Turn the "Left/Right" switch to the left，Receiver right wheel advances to open，The display display turns left

Turn the "Left/Right" switch to the right，Receiver revolver advance opens，The display display turns right

6、Turning in place

Turn left in place：Press and hold the Enable button，Move the "turn left/right" switch to the left turn position，Receiver left wheel reverse and right wheel forward open，Start turning left in place；

Turn right in place：Press and hold the Enable button，Move the "turn left/right" switch to the right turn position，Receiver left wheel forward and right wheel reverse open，Start turning right in place；

7、emergency stop

Take the emergency stop button，Receiver emergency stop output is disconnected；All switches are off，All speeds cleared；

8、Straight line correction

When the left and right motor is moving forward and backward，There is a difference in the left and right speeds，Straight-line walking is offset，The linear deviation correction function of the remote control can be used，Fine-tune the speed of left and right wheels；

Principle of correction：Through bias correction function，Fine-tune revolver speed，To achieve the same speed as the right wheel，Realize the synchronization of left and right wheel speeds，Eliminate offsets；

Correction operation method：Press and hold the Enable button，Slowly turn the "Linear Correction" knob；

Rotate clockwise，Increase the revolver speed voltage，Increased deviation correction value of the display screen；

Rotate counterclockwise，Reduce the revolver speed voltage，The display deviation correction value is reduced；

Correction range：Correction value -90 to 90；1The correction voltage of a correction unit is about 0.04V；

9、Parameter menu (user prohibits private modification)

Enter parameter menu mode：When grinding is 0，Forward/reverse rotation 3 times in a row，Break it off 3 more times；

Exit method：Choose to save or not save，Press the enable button to confirm；

Linear fine adjustment range：0-120；

Grinding speed：0-3000；

walking speed：0-1000；

Receiver operating power supply	DC24V/1A (independent power supply)
Receiver output point load	AC0-250V/3A DC0-30V/5A
Receiver speed regulation output voltage	DC0-10V

The final right to interpret this product belongs to Chengdu Xinshen Technology Co., Ltd.。

Automatic cutting wireless remote control of wire saw machine DH12S-P6S

xinhecheng — Fri, 01 Dec 2023 03:09:23 +0000

model：DH12S-P6S adapter equipment：Wire saw/blade saw machine

Remark：Three types of antennas can be selected，The default suction cup antenna is equipped with standard

Main motor speed：host：0-50
Travel motor speed：OK：0-50
Automatic cutting travel motor maximum speed limit：speed：0-30(The parameters are adjustable)
Automatic cutting main motor set current：set up：28(The parameters are adjustable)
Swing arm motor speed：put：0-50

Low pressure：The battery of the remote control is too low，Please replace the battery

Fall out of the internet：Wireless signal interruption，Please check the receiver power supply，Power on again，Restart the remote control

1、Remote control turned on

The receiver is powered on，The D2 power supply light on the receiver is always on，D1 signal light starts to flash；Two No. 5 batteries installed on the remote control，Turn on the power switch，Display display motor speed，It means the startup is successful。

2、Main motor and speed regulation
Press and hold "Speed control enable"，Turn the "Forward/Reverse" switch to forward，The main motor of the receiver rotates forward and turns on；

Press and hold "Speed control enable"，Turn the "Forward/Reverse" switch to reverse，Receiver main motor reverses and turns on；

Simply move the switch to the middle or reverse，The main motor stops immediately，No need to press speed control to enable；

Turn the "Big Motor" knob，The speed regulation voltage of the receiver main motor inverter can be adjusted 0-10V；
3、Walking motor

Press and hold "Speed control enable"，Turn the "Forward/Reverse" switch to forward or backward，The walking motor will move at a high speed of 50；

4、Swing arm motor and speed regulation

Turn the "Swing Arm/Return" switch to the swing arm or back，The swing arm motor of the receiver starts；Then turn the "speed adjustment" knob，Can adjust the speed of the swing arm motor；

Press and hold "Speed control enable"，Then flip the "swing arm/reverse" switch，The swing arm motor will move at a high speed of 50；

5、Travel motor speed limit adjustment

Press and hold the "Speed Enable" button，Turn "Speed Adjustment" to adjust the maximum speed limit of the traveling motor during automatic cutting.；

6、Automatic cutting

first step，Start the main motor；Step 2，Adjust the maximum speed limit of the traveling motor；Step 3，Turn the "forward/reverse" switch to move forward or backward，Enter automatic cutting mode；

7、Parameter settings (users prohibit private modification)

Enter the parameter menu：In manual mode，When the main motor speed is 0，Forward/reverse switch is bent up 3 times in a row，Then break it 3 times in a row，Enter the parameter menu；

Exit the Parameters Menu：Speed adjustment knob page turn，Choose to save or not save，Press the enable button to confirm；

Rated current:Maximum value of main motor current，Unit Ampere；

Speed regulation parameters:Automatic cutting control parameters，Default 800，Unit milliseconds，Modification is prohibited；

Deceleration parameters:When the cutting current change value exceeds this value，Start to decelerate rapidly，Unit Ampere；

Acceleration a1:When the cutting current is lower than the set cutting current，The speed value of each acceleration of the walking motor；

Deceleration a2: When the cutting current is higher than the set cutting current，The speed value of the walking motor reduces each time it decelerates；

Swing arm current:default value，Modification is prohibited；
Stop time:After shutdown due to current overload in automatic mode，Check the current again after a period of time，If it is less than the set current，Automatically start the walking motor；Unit second，default value，Modification is prohibited；

Maximum current:Main motor feedback current range，Unit Ampere；

Maximum host:Remote control main motor speed display range；

Maximum walking:Invalid parameter；

Speed limit offset:When cutting automatically,Remote control display walking motor speed limit = 50% of this parameter；

Add sensitivity:When the feedback current of the main motor increases，The value increased each time exceeds this value，Walking motor acceleration；

Reduce sensitivity:Main motor feedback current decreases，The value reduced each time exceeds this value，Walking motor slows down；

Sensitivity offset:The offset increase of the adding and subtracting sensitivity parameters；
Set current:Automatic cutting，The threshold for feedback current of main motor，More than this value，The walking motor starts to slow down；Below this value，The walking motor starts to accelerate；Unit Ampere；

Empty exit:When automatic mode starts，If the main motor feedback current is less than this value，is in idling mode，greater than this value，then exit idling mode，Enter cutting mode，Unit Ampere；

No-load current:When automatic mode starts，If the main motor feedback current is less than this value，is in no-load mode，greater than this value，then exit the no-load mode，Enter cutting mode，Unit Ampere；

Swing arm speed:Swing arm motor startup speed；

cutting mode:Switch between blade saw and wire saw modes，After switching, the parameters will also switch accordingly.；In blade saw mode，A swing arm motor is added to the remote control display，The wire saw mode does not have a swing arm motor.；

Debounce time:When the main motor feedback current exceeds the stop current，Will continuously detect the feedback current，The debounce time is the duration of this continuous detection.，exceed this time，Detect that the main motor current still exceeds the stop current，walkThe motor will stop；Otherwise, the walking motor will continue to move forward；

stop current:The feedback current of the main motor exceeds this value，The walking motor will stop；Unit Ampere；

Offset default:The initial value of the speed limit of the traveling motor when the remote control is turned on = 50% of this value；

Receiver operating power supply	DC24V/1A (independent power supply)
Receiver output point load	AC0-250V/3A DC0-30V/5A
Receiver speed regulation output voltage	DC0-10V

The final right to interpret this product belongs to Chengdu Xinshen Technology Co., Ltd.。