Other machinery – Core Synthesis Technology https://www.wixhc.com/cn CNC industry leader Tue, 18 Nov 2025 08:27:48 +0000 en-US hourly 1 https://wordpress.org/?v=6.8.5 Wireless electronic handwheel DWGP https://www.wixhc.com/cn/product/%e6%97%a0%e7%ba%bf%e7%94%b5%e5%ad%90%e6%89%8b%e8%bd%aedwgp Tue, 18 Nov 2025 08:11:58 +0000 https://www.wixhc.com/cn/?post_type=product&p=117811


Wireless electronic handwheel is used for manual guidance of CNC machine tools、position、Strike operation。This product useswireless transmission technology，Eliminates traditional spring wire connections，Reduce equipment failures caused by cables，exemptcable drag，Disadvantages such as oil stains，More convenient operation。Widely used in gantry machining centers、Longmenlitype lathe、CNC gear processing machine tools and other CNC machine tools，And it can be adapted to a variety of CNC systems on the market，For example, Siemens、Mitsubishi、Fanako、New generation of CNC system brands。

1.Adopt 433MHZ wireless communication technology，Wireless operation distance 80 meters；
2.Adopt automatic frequency hopping function，Use 32 sets of wireless remote controls at the same time，No effect on each other；
3.Support emergency stop button，And after the handwheel is turned off，Operating the emergency stop button is still effective；
4.Supports 6 custom buttons，Switching quantity IO signal output；
5.Support 6-axis control，Customizable 7-12 axis control；
6.Supports 3-speed multiplier control，Customizable 4-speed magnification control；
7.Support enable button function，Can output the switch quantity IO signal，You can also control the axis selection、Magnification and encoder；
8.Supports axis selection and magnification to modify the encoding type through software；
9.Support pulse encoder，Specification 100 pulses/circle；

10.Supports standard Type-C charging，5V-2A charging specifications，Built-in battery specification 14500/1100mAh。

Handheld terminal working voltage and current 3.7V/16mA
Rechargeable battery specifications
3.7V/14500/1100mAh
Handheld terminal low voltage alarm range
<3.35V
Receiver power supply voltage
DC5V-24V/1A
Receiver emergency stop output load range AC125V-1A/DC30V-2A
Receiver enables output load range AC125V-1A/DC30V-2A
Receiver custom button output load range DC24V/50mA
Receiver axis selects output load range DC24V/50mA
Receiver magnification output load range DC24V/50mA
Handheld transmit power 15dBm
Receiver Receive Sensitivity
-100dBm
Wireless communication frequency 433MHz band
Wireless communication distance Accessible distance 80 meters
Operating temperature -25℃<X<55℃
Anti-fall height 1(rice)
Customize the number of buttons
6(indivual)
Product weight 517.5（g）
Product size 185*87*68（mm）

Comments：
①Emergency stop button：
Press the emergency stop button，Two groups of emergency stop IO outputs on the receiver are disconnected，And all functions of the handwheel are invalid。Release emergency stop，Emergency stop IO output closed on the receiver，All functions of the handwheel are restored；and close the handwheelAfter power，Press the emergency stop button，The emergency stop IO output of the receiver is still effective。
②Enable button：
Press any enable button on both sides，Two groups on the receiver enable IO output conduction，Release the enable buttonbutton，Enable IO output disconnection；And select the plurality in the switching axis，and before shaking the handwheel，Need to holdThe button is enabled；This feature can be cancelled by configuring the software。
③Axis selection switch (power switch)：
Press and hold the enable button，Switching the axis selection switch can switch the moving axis controlled by the handwheel。Change this switch fromOFF gear switches to any axis，Handwheel power supply。
④Pulse encoder：

Press and hold the enable button，Shaking pulse encoder，Send a pulse signal，Control the machine shaft movement。

⑤Battery light：
Hand wheel power display，Full light means full battery，All off means it is not powered on or has no power.，No. on the leftOne level of battery flashes，Indicates the battery is too low，Please charge it in time。
⑥Signal light：
The signal light is on，Indicates that the handwheel is being operated，And the signal is normal；If the signal light is off, it means there is no currentThere is operation，or operating，But the wireless signal is not connected。
⑦Custom buttons：
6Custom buttons，Each button corresponds to an IO output point on the receiver。
⑧Magnification switch：
Press and hold the enable button，Switch the magnification switch，The multiplier can be switched by handwheel control。
⑨Charging port：
Built-in rechargeable battery，Charging with Type-C specification charger，Charging voltage 5V，Charging current1A-2A；Charging time 3-5 hours。 While charging，Battery light flashes，Indicates charging，After full，Battery display is full，No flashing。



Product installation steps：
1.Install the receiver in the electric cabinet through the snap-on on the back，Or through the screw holes at the four corners of the receiverInstall it in the electrical cabinet。
2.Refer to our receiver wiring diagram，Compare your on-site equipment，Connect the device through the cable and receiver
connect。
3.After the receiver is fixed，The antenna equipped with the receiver must be connected，And install the outer end of the antenna oror placed outside the electrical cabinet，It is recommended to place the signal on the top of the electric cabinet.，It is not allowed to disconnect the antenna，or willThe antenna is placed inside the electrical cabinet，It may cause the signal to be unusable。

4.Finally turn on the handwheel power switch，You can operate the handwheel remote control machine。

Receiver installation size：

Receiver Wiring Reference Diagram：

1.The machine is powered，The receiver is powered on，The receiver operating light is on，Install the wireless electronic handwheel
pool，Tighten the battery cover，Turn on the wireless electronic handwheel power switch，Handwheel power lights on；
2.Select the axis：Press and hold the enable button，Switch axle selection switch，Select the axis you want to operate；
3.Select the multiplier：Press and hold the enable button，Switch the magnification switch，Select the multiplier you need；
4.Move the axis：Press and hold the enable button，Select the axis and switch，Select the multiplier switch，Then turn the pulse encoder
coder，Turn clockwise forward movement axis，Turn the negative movement axis counterclockwise；
5.Press and hold any custom button，The corresponding button IO output of the receiver is turned on，Release button output close；
6.Press the emergency stop button，The receiver disconnects the emergency stop IO output，Handwheel function fails，Release the emergency stop button
button，Emergency stop IO output closed，Handwheel function recovery；
7.Not operating the handwheel for a while，The handwheel automatically enters sleep standby，Reduce power consumption，When using again，
The handwheel can be activated by pressing the enable button；
8.Don't use the handwheel for a long time，It is recommended to select the handshake to OFF gear，Turn off the handwheel，extend
Battery life。

①：DWGP stands for Appearance Style
②：Pulse output parameters：
01：Indicates that the pulse output signal is A、B；Pulse voltage 5V；Pulse number 100PPR；
02：Indicates that the pulse output signal is A、B；Pulse voltage 12V；Pulse number 25PPR;
03：Indicates that the pulse output signal is A、B、A-、B-；Pulse voltage 5V；Pulse number 100PPR；
04：Indicates low level NPN open circuit output，The pulse output signal is A、B；Pulse number 100PPR；
05：Indicates high level PNP source output，The pulse output signal is A、B；Pulse number 100PPR；
③：Represents the number of axis selection switch axes，6Represents 6 axes，7Represents 7 axes，and so on；
④：Represents the axis selection switch signal type，A represents point-to-point output signal，B represents the coded output signal；
⑤：Represents the signal type of the magnification switch，A represents point-to-point output signal，B represents the coded output signal；
⑥：Represents the number of custom buttons，6Represents 6 custom buttons；

⑦：Representative system handwheel power supply，05Represents 5V power supply，24Represents 24V power supply。

Fault situation Possible Cause Troubleshooting Methods
Turn the OFF switch，
Cannot turn on，
The power light does not light up
1.The handwheel is not installed with battery
Or the battery installation is abnormal
2.Insufficient battery power
3.Handwheel failure
1.Check the installation of handwheel battery
2.Charge the handwheel
3.Contact the manufacturer to return to the factory for maintenance
Handwheel boot，
No response to operation，
During operation，The handwheel signal light does not light up
1.The receiver is not powered
2.Receiver antenna not installed
3.The distance between the remote control and the machine is too far
4.Environmental interference
5.The enable is not pressed and held while the handwheel is operated
Button
1.Check the receiver power on
2.Install the receiver antenna，And make the sky
The outer end of the wire is installed and fixed outside the electrical cabinet.
3.Operation at normal distance
4.① Optimize the wiring of the electric cabinet，Receiver
Keep the antenna wiring as far away as possible from 220V and above
Use the power supply of the line ② receiver as much as possible
Powered by an independent switching power supply，and
Add power isolation module and
magnetic ring，Increase anti-interference ability
Handwheel boot，
Battery light flashes
1.Insufficient battery power
2.Battery installation or poor contact
1.Charge the handwheel
2.Check battery installation，as well as
Are the metal sheets at both ends of the battery compartment dry?
No foreign objects，Clean it
Press the button by handwheel，
Or turn the switch，
or shake pulse encoder
No response
1.Switch/button/pulse encoder
Damage fault
2.Receiver damage fault
1.Watch the switch or press the button
or when shaking the pulse encoder，hand wheel
Is the signal light flashing?，Not bright
Table switch or button or encoder failure，
Return to factory maintenance；Light means normal，Inspection
Check whether the receiver wiring is correct
2.Return to factory maintenance
After the receiver is powered on，
No light on the receiver
1.Power supply abnormality
2.Power wiring error
3.Receiver failure
1.Check if the power supply has voltage，
Does the voltage meet the requirements
2.Check whether the positive and negative poles of the power supply are connected in reverse
3.Return to factory maintenance

1.Please at room temperature and pressure，Used in dry environments，Extend service life；
2.Please avoid getting wet in the rain、Used in abnormal environments such as blisters，Extend service life；
3.Please keep the handwheel clean，Extend service life；
4.Please avoid squeezing、Fall、Bumping, etc.，Prevent precision accessories inside the handwheel from damage or accuracy errors；
5.Not used for a long time，Please store the handwheel in a clean and safe place；
6.Pay attention to moisture-proof and shock-proof during storage and transportation。
1.Please read the instructions for use in detail before use，Non-professional personnel are prohibited；
2.Please charge in time when the battery is too low，Avoid errors caused by insufficient power, causing the handwheel to be unable to operate；
3.If repair is required，Please contact the manufacturer，If damage caused by self-repair，The manufacturer will not provide a warranty。
]]> LXWGP-ETS-SIEMENS wired electronic handwheel https://www.wixhc.com/cn/product/lxwgp-ets-siemens%e6%9c%89%e7%ba%bf%e7%94%b5%e5%ad%90%e6%89%8b%e8%bd%ae Mon, 20 Oct 2025 05:30:08 +0000 https://www.wixhc.com/cn/?post_type=product&p=117808

Electronic handwheel is used for manual guidance of CNC machine tools、position、Strike operation。This model of electronic handwheel is a Siemens wired electronic handwheel with real display.，The handwheel is connected to the X130 interface of the Siemens system through a network cable.，Read the system coordinates and display them to the LCD display of the handwheel through S7 protocol communication.，And the handwheel control system axis selection can be made through communication.、magnification、Button and other signals。

1.Connected using 6-core aviation plug cable，Handwheel cable length 10 meters。
2.The handwheel screen can display the system workpiece coordinates、Mechanical coordinates、Feed speed、Axis selection、Information such as magnification。
3.Support emergency stop button，Switching quantity IO signal output，Handwheel shutdown emergency stop is still effective。
4.Supports 6 custom buttons，Switching IO signal，Can output signals to the system through IO wiring or communication。
5.Supports 6 or 8 axis control，Switching IO signal，Can output signals to the system through IO wiring or communication。
6.Support 3 or 4 levels of magnification control，Switching IO signal，Can output signals to the system through IO wiring or communication。
7.Support pulse encoder，100Pulse/Circle，The signal can be output to the system through AB pulse wiring.。
8.Support Siemens S7 protocol，Support Siemens 828D、840DSL、ONE and other model systems。

Handwheel working power supply voltage DC24V/1A
Receiver power supply voltage DC24V/1A
Receiver IO output load range
DC24V
Handwheel end cable length
10m
Receiver end cable length
1m
Receiver end network cable length
3m
Operating temperature
-25℃<X<55℃
Anti-fall height
1m
Customize the number of buttons 6indivual
Product size 233*90.7*77.4（mm）

 


Comments：
①Emergency stop button：
Press the emergency stop button，Two groups of emergency stop IO outputs on the receiver are disconnected，And all functions of the handwheel are invalid。
After the emergency stop is released，Emergency stop IO output closed on the receiver，All functions of the handwheel are restored。

②Screen display：

PLC：0000It means the network cable is not connected，PLC：1010It means the network cable and PLC system are connected successfully.，

PLC：1110Indicates that the handwheel writes system data successfully.，PLC：0001Indicates successful connection to computer。

③Custom button：
6Custom buttons，Each button corresponds to an IO output point on the receiver，Also connected to the system through communication。
④Axis selection switch：
Switching the axis selection switch can switch the moving axis controlled by the handwheel。
⑤Enable button：
Press and hold either enable button on either side，It is effective only by shaking the pulse encoder。 And the 2 sets of enabled IO outputs on the receiver are turned on，Release the enable button，Enable IO output disconnection。
⑥Magnification switch：
Switching the magnification switch can switch the magnification controlled by the hand wheel.。
⑦Pulse encoder：
Press and hold the enable button，Shaking pulse encoder，Send a pulse signal，Control the machine shaft movement。
⑧Hand wheel cable：

Cable connecting handwheel and receiver，aviation plug，For handwheel power supply and communication。



6.1Product installation steps
1.Install the receiver in the electrical cabinet through the screw holes at the four corners.。
2.Refer to our receiver wiring diagram，Compare your on-site equipment，Connect the device through the cable and receiver
connect，Use a network cable to connect the receiver to the X130 interface of the system。
3.After the receiver is fixed，Install the aviation plug base into the handwheel opening on the panel，Another base
The terminal strip is plugged into the handwheel interface on the receiver.。Then insert the aviation plug of the handwheel end cable into the base，Tighten
fixtures。
6.2Receiver installation size

6.3Aviation plug installation dimensions

6.4Receiver Wiring Reference Diagram

1.The receiver is powered on，The receiver operating light is on，Connect the receiver to the computer using a network cable，Set a fixed IP address for your computer，Use the network configuration tool software to set network parameters for the handwheel function，Specific settings
For the method, please refer to "Instructions for Use of LXWGP-ETS Wired Handwheel"。
2.After receiver setup is complete，The system requires programming PLC program，For details, please refer to "LXWGP-ETS Setting Methods for Different Siemens CNC Systems" and PLC program routine information。
3.After the above settings are completed，Take the receiver to the machine electrical cabinet and install it，Unplug the network cable from the computer and plug it into the X130 interface of the system，Plug in the receiver power and pulse wires。
4.The machine is powered，The receiver is powered on，The receiver operating light is on，Turn on the handwheel power switch，Handwheel screen boot，Screen display PLC:1010，Indicates successful communication between the handwheel and the system.。
5.Select axis selection：Switch axle selection switch，Select the axis you want to operate。
6.Select the multiplier：Switch the magnification switch，Select the multiplier you need。
7.Move the axis：Press and hold the enable button，Select the axis and switch，Select the multiplier switch，Then turn the pulse encoder，Turn clockwise forward movement axis，Turn the negative movement axis counterclockwise。
8.Press and hold any custom button，The corresponding button IO output of the receiver is turned on，Release button output close。
9.Press the emergency stop button，The receiver disconnects the emergency stop IO output，Handwheel function fails，Release the emergency stop button，Emergency stop IO output closed，Handwheel function recovery。



Fault situation Possible Cause
Troubleshooting Methods
Troubleshooting Methods
1.Whether the aviation cable between the handwheel and the receiver is connected correctly and reliably
2.Is the receiver power voltage sufficient?
3.Handwheel failure
1.Check the connection of the aviation cable between the handwheel and the receiver
2.Check receiver input power
3.Contact the manufacturer to return to the factory for maintenance
No response when operating the handwheel
1.Are the network cables between the receiver and system connected?
2.Is the system PLC program written well?
3.Is the receiver configuration set correctly?
4.Is the 485 communication icon displayed on the handwheel display failed?
5.When operating the handwheel，You need to press and hold the enable buttons on both sides
6.Is the emergency stop button released?
1.Check whether the receiver and system X130 network port are connected with a network cable
2.Check and confirm whether the system PLC is written according to the reference materials we provided.
3.Check whether the receiver refers to our information and provided tool software，Correctly set the network parameters and DB address of the receiver, etc.
4.Check between handwheel and receiver
6core green socket，Two of the communication lines：485-A and 485-B，Is it correctly and securely connected?，Is there any circuit break?
After the receiver is powered on，The work light on the receiver does not light up
1.Power supply abnormality
2.Power wiring error
3.Receiver failure
1.Check if the power supply has voltage，
Does the voltage meet the requirements
2.Check whether the positive and negative poles of the power supply are connected in reverse
3.Return to factory maintenance

1.Please at room temperature and pressure，Used in dry environments，Extend service life。
2.Please avoid getting wet in the rain、Used in abnormal environments such as blisters，Extend service life。
3.Please keep the handwheel clean，Extend service life。
4.Please avoid squeezing、Fall、Bumping, etc.，Prevent precision accessories inside the handwheel from damage or accuracy errors。
5.Not used for a long time，Please store the handwheel in a clean and safe place。
6.Pay attention to moisture-proof and shock-proof during storage and transportation。

1.Please read the instructions for use in detail before use，Non-professional personnel are prohibited。
2.After any abnormal situation occurs in the handwheel，Please stop using it immediately，and troubleshoot，Before troubleshooting，It is forbidden to use the faulty handwheel again，Avoid safety accidents due to unknown handwheel failures；
3.If repair is required，Please contact the manufacturer，If damage caused by self-repair，The manufacturer will not provide a warranty。
]]> Special wireless electronic handwheel for CNC mount https://www.wixhc.com/cn/product/%e6%95%b0%e6%8e%a7%e7%ab%8b%e8%bd%a6%e4%b8%93%e7%94%a8%e6%97%a0%e7%ba%bf%e7%94%b5%e5%ad%90%e6%89%8b%e8%bd%ae Thu, 21 Aug 2025 03:52:54 +0000 https://www.wixhc.com/cn/?post_type=product&p=117700

Special wireless electronic handwheel for CNC vertical car is used for manual guidance of CNC vertical machine tools、position、Strike operation。This product uses wireless transmission technology，Eliminates traditional spring wire connections，Reduce equipment failures caused by cables，Free cable drag，Disadvantages such as oil stains，More convenient operation。Widely applicable to CNC vertical lathes、Single column vertical lathe、Double column vertical lathes and other vertical lathes。And it can be adapted to a variety of CNC systems on the market，For example, Siemens、Mitsubishi、Fanako、New generation of CNC system brands。

1.Adopt 433MHZ wireless communication technology，Wireless operation distance 40 meters。
2.Adopt automatic frequency hopping function，Use 32 sets of wireless remote controls at the same time，No effect on each other。
3.Support emergency stop button，Switching quantity IO signal output。
4.Supports 2 custom buttons，Switching quantity IO signal output。
5.Supports 2-axis control。
6.Supports 3-speed multiplier control。
7.Support enable button function，Can output the switch quantity IO signal，You can also control the axis selection、Magnification and encoder。
8.Supports axis selection and magnification to modify the encoding type through software。
9.Support pulse encoder，Specification 100 pulses/circle。

Handheld terminal working voltage and current 3 In/14 mA
Battery specifications 2No. 5 AA alkaline battery
Handheld terminal low voltage alarm range
<2.3V
Receiver power supply voltage DC5V-24V/1A
Receiver emergency stop output load range AC125V-1A/DC30V-2A
Receiver enables output load range AC125V-1A/DC30V-2A
Receiver custom button output load range DC24V/50mA
Receiver axis selects output load range DC24V/50mA
Receiver magnification output load range DC24V/50mA
Handheld transmit power
15dBm
Receiver Receive Sensitivity -100dBm
Wireless communication frequency
433MHz band
Wireless communication distance
Accessible distance 40 meters
Operating temperature -25℃<X<55℃
Anti-fall height Comply with national testing standards
Customize the number of buttons (2 pieces)

Right column handwheel(Right knife handle wheel)
model：ZTWGP03-2AA-2-05-R

Left column handwheel(Left knife handle handwheel)
model：Ztwgp03-2aa-2-05-l
Right column handwheel(Right knife handle wheel)
model：STWGP03-2AA-2-05-R

Left column handwheel(Left knife handle handwheel)
model：STWGP03-2AA-2-05-L

Comments：

①Pulse encoder：
Press and hold the enable button，Shaking pulse encoder，Send a pulse signal，Control the machine shaft movement。
②Enable button：
Press any enable button on both sides，Two groups on the receiver enable IO output conduction，Release the enable button，Enable IO output disconnection；And select the plurality in the switching axis，and before shaking the handwheel，You need to hold the enable button to be effective；This feature can be cancelled by configuring the software。
③ Indicator light：
Left light：Turn on the light，Use the shaft of the handwheel to turn on the machine，This light is always on after turning on；
Middle light：Signal light，When operating any function of the handwheel，This light is on，Not lighted when no operation；
Right side light：Low voltage alarm light，Battery power is too low，This light flashes or is always on，Need to replace the battery。
④Emergency stop button：
Press the emergency stop button，Two groups of emergency stop IO outputs on the receiver are disconnected，And all functions of the handwheel are invalid。

Release emergency stop，Emergency stop IO output closed on the receiver，All functions of the handwheel are restored。

⑤Maximization switch：
Press and hold the enable button，Switch the magnification switch，The multiplier can be switched by handwheel control。
⑥Axis selection switch (power switch)：
Press and hold the enable button，Switching the axis selection switch can switch the moving axis controlled by the handwheel。Switch this switch from OFF to any axis，Handwheel power supply。
⑦Custom buttons：
2Custom buttons，Each button corresponds to an IO output point on the receiver。
Product installation steps
1.Install the receiver in the electric cabinet through the snap-on on the back，Or install it in the electrical cabinet through the screw holes at the four corners of the receiver.。
2.Refer to our receiver wiring diagram，Compare your on-site equipment，Connect the device through a cable and a receiver。
3.After the receiver is fixed，The antenna equipped with the receiver must be connected，And install the outer end of the antenna or place it outside the electric cabinet，It is recommended to place the signal on the top of the electric cabinet.，It is not allowed to disconnect the antenna，Or place the antenna inside the electric cabinet，It may cause the signal to be unusable。
4.Finally turn on the handwheel power switch，You can operate the handwheel remote control machine。
Receiver installation size

Receiver Wiring Reference Diagram

1.The machine is powered，The receiver is powered on，The receiver operating light is on，Wireless electronic handwheel battery installed，Tighten the battery cover，Turn on the wireless electronic handwheel power switch，Handwheel power lights on。
2.Select the axis：Press and hold the enable button，Switch axle selection switch，Select the axis you want to operate。
3.Select the multiplier：Press and hold the enable button，Switch the magnification switch，Select the multiplier you need。
4.Move the axis：Press and hold the enable button，Select the axis and switch，Select the multiplier switch，Then turn the pulse encoder，Turn clockwise forward movement axis，Turn the negative movement axis counterclockwise。
5.Press and hold any custom button，The corresponding button IO output of the receiver is turned on，Release button output close。
6.Press the emergency stop button，The receiver disconnects the emergency stop IO output，Handwheel function fails，Release the emergency stop button，Emergency stop IO output closed，Handwheel function recovery。
7.Not operating the handwheel for a while，The handwheel automatically enters sleep standby，Reduce power consumption，When using again，The handwheel can be activated by pressing the enable button。

8.Don't use the handwheel for a long time，It is recommended to select the handshake to OFF gear，Turn off the handwheel，Extend battery life。

①：ZTWGP stands for appearance style

②：Pulse output parameters：
01：Indicates that the pulse output signal is A、B；Pulse voltage 5V；Pulse number 100PPR。
02：Indicates that the pulse output signal is A、B；Pulse voltage 12V；Pulse number 25PPR。
03：Indicates that the pulse output signal is A、B、A-、B-；Pulse voltage 5V；Pulse number 100PPR。
04：Indicates low level NPN open circuit output，The pulse output signal is A、B；Pulse number 100PPR。
05：Indicates high level PNP source output，The pulse output signal is A、B；Pulse number 100PPR。
③：Represents the number of axis selection switch axes，2Represents 2 axes。
④：Represents the axis selection switch signal type，A represents point-to-point output signal，B represents the coded output signal。
⑤：Represents the signal type of the magnification switch，A represents point-to-point output signal，B represents the coded output signal。
⑥：Represents the number of custom buttons，2Represents 2 custom buttons。
⑦：Representative system handwheel power supply，05Represents 5V power supply。
⑧：L represents the left column (left knife holder)，R represents the right column (right knife holder)。

Fault situation Possible Cause
Troubleshooting Methods
Turn the OFF switch，
Cannot turn on，
The power light does not light up
1.The handwheel is not installed with battery
Or the battery installation is abnormal
2.Insufficient battery power
3.Handwheel failure
1.Check the installation of handwheel battery
2.Replacement battery
3.Contact the manufacturer to return to the factory for maintenance
Handwheel boot，
No response to operation，
During operation，Handwheel signal
The light does not light up
1.The receiver is not powered
2.Receiver antenna not installed
3.The distance between the remote control and the machine is too far
4.Environmental interference
5.The enable is not pressed and held while the handwheel is operated
Button
1.Check the receiver power on
2.Install the receiver antenna，Install the outer end of the antenna outside the electric cabinet to fix it
3.Operation at normal distance
4.① Optimize the wiring of the electric cabinet，The receiver antenna wiring should be kept away from 220V and
On line ② Try to use independent switching power supply to supply the receiver power supply as much as possible，and
Power cord adds power isolation module and magnetic ring，Increase anti-interference ability
Handwheel boot，
Low voltage alarm light flashes
1.Insufficient battery power
2.Battery installation or poor contact
1.Replacement battery
2.Check battery installation，And whether the metal sheets at both ends of the battery compartment are dry
No foreign objects，Clean it
Press the button by handwheel，
Or turn the switch，
or shake pulse encoder，
No response
1.Switch/button/pulse encoder
Damage fault
2.Receiver damage fault
1.Watch the switch or press the button
or when shaking the pulse encoder，Is the handwheel signal light lit?，Not bright
Table switch or button or encoder failure，Return to factory maintenance；Light means normal，Inspection
Check whether the receiver wiring is correct
2.Return to factory maintenance
After the receiver is powered on，
No light on the receiver
1.Power supply abnormality
2.Power wiring error
3.Receiver failure
1.Check if the power supply has voltage，Does the voltage meet the requirements
2.Check whether the positive and negative poles of the power supply are connected in reverse
3.Return to factory maintenance

1.Please at room temperature and pressure，Used in dry environments，Extend service life。
2.Please avoid getting wet in the rain、Used in abnormal environments such as blisters，Extend service life。
3.Please keep the handwheel clean，Extend service life。
4.Please avoid squeezing、Fall、Bumping, etc.，Prevent precision accessories inside the handwheel from damage or accuracy errors。
5.Not used for a long time，Please store the handwheel in a clean and safe place。
6.Pay attention to moisture-proof and shock-proof during storage and transportation。
1.Please read the instructions for use in detail before use，Non-professional personnel are prohibited。
2.Please replace the battery in time when the battery is too low，Avoid errors caused by insufficient power, causing the handwheel to be unable to operate。
3.If repair is required，Please contact the manufacturer，If damage caused by self-repair，The manufacturer will not provide a warranty。
]]> Track car rope saw cutting remote control DH22S-LD-485 https://www.wixhc.com/cn/product/%e5%b1%a5%e5%b8%a6%e8%bd%a6%e7%bb%b3%e9%94%af%e5%88%87%e5%89%b2%e9%81%a5%e6%8e%a7%e5%99%a8-dh22s-ld-485 Mon, 12 May 2025 05:15:57 +0000 https://www.wixhc.com/cn/?post_type=product&p=117676

1.Product introduction

Crawler wire saw automatic cutting remote control is suitable for crawler wire saw cutting machines，The 485Modbus RTU protocol is used to control the left and right crawler inverter speed regulation start and front, rear, left and right direction control.，And large motor frequency converter speed regulation start。And the working current of the large motor inverter can be read through the 485-Modbus RTU protocol，Analysis and comparison of large motor currents，Automatically adjust left and right track speeds in real time，Realize automatic cutting function。

 

2.Product features

1.Adopt 433MHZ wireless communication technology，Wireless operating distance 100 meters。

2.Adopt automatic frequency hopping function，Use 32 sets of wireless remote controls at the same time，No effect on each other。

3.Supports all frequency converters with 485 modbus RTU protocol，The currently adapted inverter brands include：Shanghai Xielin、Fuji、Huichuan、Zhongchen、INVT、Yasukawa Tatsu。If the brand is not adapted, please contact us for customization.。

4.Support large motor frequency converter speed regulation、start up、Current reading。

5.Support left and right crawler inverter speed adjustment、start up、Front and rear left and right controls。

6.Support left and right crawler inverter linear correction，Keep the machine moving in a straight line。

7.Support wire saw automatic cutting function，According to the large motor current information，Automatically adjust left and right track speeds in real time。

8.It is also compatible with direct IO output to control motor start and stop.，Analog voltage output controls motor speed。

3.product specifications

Handheld terminal working voltage and current 2AA battery-3V/10mA
Receiver operating voltage and current 24V/1A
Handheld transmit power 15dBm
Receiver Receive Sensitivity -100dBm
Wireless communication frequency 433Mhz frequency band
Operating temperature -25℃<X<55℃
Anti-fall height Comply with national testing standards
Waterproof level Ip67
Product size 225*84*58（mm）

 

4.Product function introduction

Comments：

①Screen display：

②Mode switch：

Adopt 2-speed switch，Can switch between automatic and manual modes，There will be a corresponding mode display switch on the display.。

③Enable：

Combination button，Some operations require pressing and holding the enable button to operate，See the description of each switch for details.。

④Large motor switch：

Adopt 3-speed reset switch，flip this switch，Can control forward and reverse rotation of large motors，The status will remain after letting go，There will be a corresponding display on the display，S1↑ arrow indicates forward rotation，S1↓ arrow indicates reversal。

⑤Small motor forward/reverse switch：

Adopt 3-speed self-locking switch，Press the enable button + flip the switch，Can control the small motor to move forward and backward，There will be a corresponding display on the display，↑↑Arrows indicate forward，↓↓The arrow indicates going back。

⑥Linear deviation correction：

Using multi-turn encoder knob，Press enable button，Turn knob right，Straight line correction display：Df：left，Each turn of the knob increases by 1 unit.，The left motor speed increases by 0.1 units；Turn knob left，Straight line correction display：Df：right，Each turn of the knob increases by 1 unit.，The right motor speed increases by 0.1 units。

⑦Small motor turning switch：

Adopt 3-speed reset switch，Turn this switch in manual mode，Can control small motor to turn left and right，The remote control will automatically stop this action after letting go.。In forward state，flip this switch，There will be a corresponding display on the display，←↑ arrow indicates left turn，↑→arrow indicates turning right。In retreat state，flip this switch，There will be a corresponding display on the display，←↓ arrow indicates left turn，↓→arrow indicates turning right。

⑧Speed ​​regulation of large motor：

Using multi-turn encoder knob，Rotate 1 frame each time，The large motor speed value changes by approximately 0.2 units，Rapid rotation can quickly modify the large motor speed value。

⑨Small motor speed regulation：

Using multi-turn encoder knob，In manual mode，Press enable button，Then rotate 1 frame each time，The speed value of the left and right small motors changes by about 0.1 unit，Quick rotation can quickly modify the speed value of the small motor。In automatic mode，Press enable button，Then rotate 1 frame each time，The small motor speed limit value F changes by about 0.1 unit，Quick rotation can quickly modify the speed limit value of small motors。

⑩Remote control power switch：

Remote control display power on。

 

5.Product accessories diagram

 

6.Product Installation Guide
6.1Product installation steps

1.Install the receiver in the electric cabinet through the snap-on on the back，Or install it in the electrical cabinet through the screw holes at the four corners of the receiver.。

2.Refer to our receiver wiring diagram，Compare your on-site equipment，Connect the device to the receiver via wires。

3.After the receiver is fixed，The antenna equipped with the receiver must be connected，And install the outer end of the antenna or place it outside the electric cabinet，It is recommended to place the signal on the top of the electric cabinet.，It is not allowed to disconnect the antenna，or will

The antenna is placed inside the electrical cabinet，It may cause the signal to be unusable。

4.Finally, install the batteries in the remote control，Tighten the battery cover，Then turn on the remote control power switch，The remote control display will show the normal working interface.，You can perform remote control operation。

6.2Receiver installation size

6.3Receiver Wiring Reference Diagram

7.Product operating instructions

7.1Remote control parameter settings
Enter the remote control background parameter method：Move the mode switch to manual mode，The speed of the small motor is adjusted to 25 on the left and right，Or both are 0、10、20、40、50，Pull the forward rotation switch of the large motor upward 3 times in a row，Pull down 3 times in succession；
Use the "Small Motor Speed ​​Adjustment" knob to turn pages，After pressing enable, turn the small motor speed control knob to modify the parameters.；
After modification，Turn the page to the end，Select Save and Exit，Press the enable button to exit the menu；
The parameters are as follows：
Maximum current：Large motor current feedback value range，Setting range 15-200A，Default 100；
Speed ​​regulation parameters：Automatic mode small motor automatically accelerates speed，The smaller, the faster，Setting range 200-1500，Default 800；
Deceleration parameters：Set the upper limit for allowed motor speed changes，When the current change exceeds this value，will slow down。
The smaller，The left and right motors decelerate faster，Range 05-12，Default 06；
Acceleration a1：The larger the motor, the faster the speed increases.，Range 00-06，Default 01；

Deceleration a2：The larger the motor speed is, the faster it will decrease.，Range 00-06，Default 02；

Enable speed adjustment：Is it necessary to press Enable to adjust the speed of small motors?，00Disable，01enable，Default 01；
Start self-locking：Will the large motor automatically maintain self-locking after the forward and reverse switch is released?，00do not maintain，01Keep，Default 01；
Maximum walking：Maximum speed of left and right motors，Range 10-100，Default 50；
Cutting current：Maximum cutting current，The screen displays the IC value，Range 15-160，Default 30，Screen corresponding display IC：30。The upper limit of this parameter = maximum current x80%；
Default speed limit：The default small motor automatic cutting speed at startup，Range 00-100，Default 10，The screen correspondingly displays F1.0，This parameter is only accurate when the maximum walk is set to 50。
Automatic mode：Set to 00，Auto/manual switch is a mode switch，Set to 01，Turn the automatic/manual switch to the automatic position，Display display lighting，Automatic terminal output closure on receiver，Hit manual，Automatic output terminal disconnection；
Speed ​​limit offset：Small motor automatic cutting speed upper limit，Range 00-200，Default 60，The screen corresponds to display 6.0；Display value upper limit = speed limit offset × 0.1；
Maximum host：Maximum speed of large motor，Range 10-100，Default 50；
mbus device (required)：Large motor inverter model selection，Range 00-03，Default 03；
00-Shanghai Xielin 01-Fuji
02-INVT 03-Huichuan (Zhongchen、Robin Kang)
sbus device (required)：Small motor inverter model selection，Range 00-05，Default 03；
00-Shanghai Xielin 01-Fuji
02-INVT 03-Huichuan (Zhongchen、Robin Kang)
04-Yaskawa Da 05-None

7.2Frequency converter parameter setting

1.Command source selection：Communication command channel

2.Main frequency source selection：communication given

3.baud rate：19200

4.Data format：No checksum，Data format<8-N-1>

5.Local address：Left frequency converter is set to 1，The right frequency converter is set to 2，Large motor inverter is set to 3

 

7.3Remote control operating instructions

1.The machine is powered，Remote control turned on，Enter the remote control background，Set the background parameters of the remote control，main

It is to set the inverter models of small motors and large motors (skip this step if the machine manufacturer has set it)；

2.Set the inverter parameters (skip this step if the machine manufacturer has set them)；

3.Switch the remote control to manual mode，Then use the remote control to move the machine to the working position；

4.In manual mode，Set the large motor cutting current setting value IC，Set the maximum motor speed；

5.Switch to automatic mode，Set the small motor cutting speed limit F value；

6.In automatic mode，Turn the big motor switch to forward to start the big motor，Then turn the small motor switch to

Forward or reverse gear，The remote control enters automatic cutting mode，Start cutting。

 

8.Product troubleshooting

Fault situation Possible Cause
Troubleshooting Methods
Press the power switch，
Cannot turn on and off，
The display does not light up
1.The battery is not installed on the remote control
Or the battery direction is installed incorrectly
2.Insufficient battery power
3.Remote control failure
1.Check the battery installation of the remote control
2.Replacement battery
3.Contact the manufacturer to return to the factory for maintenance
Remote control turned on，
Shows network outage and emergency stop!
Please try again!
1.The receiver is not powered
2.Receiver antenna not installed
3.The distance between the remote control and the machine is too far
4.Environmental interference
5.Before turning on the remote control，The receiver must be powered on first，Turn on the remote control again
1.Check the receiver power on
2.Install the receiver antenna，Install the outer end of the antenna outside the electric cabinet to fix it
3.Operation at normal distance
4.① Optimize the wiring of the electric cabinet，Keep the receiver antenna wiring as far away as possible from 220V and above lines. ② Try to use an independent switching power supply for the receiver power supply.，And add power isolation module and magnetic ring to the power cord.，Increase anti-interference ability
Remote control turned on，show chage battery
1.Insufficient battery power
2.Battery installation or poor contact
1.Replacement battery
2.Check battery installation，And whether the metal sheets at both ends of the battery compartment are clean and free of foreign matter，Clean it
Some buttons on the remote control
Or the switch does not respond
1.Switch damage failure
2.Receiver damage fault
1.Observe when flipping the switch，Is there a corresponding arrow on the display screen?；There is an arrow displayed，Indicates that the switch is normal；No arrow displayed means the switch is broken.，Return to factory maintenance
2.Return to factory maintenance
After the receiver is powered on，No light on the receiver
1.Power supply abnormality
2.Power wiring error
3.Receiver failure
1.Check if the power supply has voltage，Does the voltage meet the requirements
2.Check whether the positive and negative poles of the power supply are connected in reverse
3.Return to factory maintenance

 

9.Maintenance and care

1.Please at room temperature and pressure，Used in dry environments，Extend service life。

2.Please avoid getting wet in the rain、Used in abnormal environments such as blisters，Extend service life。

3.Please keep the battery compartment and metal shrapnel area clean。

4.Please avoid squeezing and dropping the remote control, which may cause damage.。

5.Not used for a long time，Please remove the battery，And store the remote control and battery in a clean and safe place。

6.Pay attention to moisture-proof and shock-proof during storage and transportation。

10.safety information

1.Please read the instructions for use in detail before use，Non-professional personnel are prohibited。

2.Please replace the battery in time when the battery is too low，Avoid errors caused by insufficient battery power causing the remote control to be inoperable.。

4.If repair is required，Please contact the manufacturer，If damage caused by self-repair，The manufacturer will not provide a warranty。

]]> Fanako special handwheel XWGP–Ets-Fanuc https://www.wixhc.com/cn/product/%e4%b8%93%e7%94%a8%e6%89%8b%e8%bd%aexwgp-ets-fanuc Tue, 06 May 2025 06:51:19 +0000 https://www.wixhc.com/cn/?post_type=product&p=117672

Wireless electronic handwheel is used for manual guidance of CNC machine tools、position、Strike operation。This product uses wireless transmission technology，Eliminates traditional spring wire connections，Reduce equipment failures caused by cables，Free cable drag，Disadvantages such as oil stains，More convenient operation。This model of wireless electronic handwheel is a special handwheel for FANUC systems.，Real-time display of FANUC system coordinates on the handwheel screen through the IO-LINK protocol，And through the IO-LINK protocol，Select the axis directly、magnification、Button signal access system，Reduce wiring。

1.Adopt 433MHZ wireless communication technology，Wireless operation distance 40 meters；
2.Adopt automatic frequency hopping function，Use 32 sets of wireless remote controls at the same time，No effect on each other；
3.Support emergency stop button，Switching quantity IO signal output，Connect to the system via IO wiring；
4.Supports 4 custom buttons，Switching IO signal，Output signals to the system through IO-LINK protocol；
5.Supports quick movement buttons + and -，Press and hold the button to move the machine instead of the handwheel；
6.Support 6-axis control，Switching IO signal，Output signals to the system through IO-LINK protocol；
7.Supports 3-speed multiplier control，Switching IO signal，Output signals to the system through IO-LINK protocol；
8.Support enable button function，Connect to the system via IO wiring，Control encoder enable at the same time；
9.Support pulse encoder，100Pulse/Circle，Access the system MPG handwheel interface by outputting AB coded signals；


Comments：
Comments：
①Emergency stop button：
Press the emergency stop button，Two groups of emergency stop IO outputs on the receiver are disconnected，And all functions of the handwheel are invalid。After the emergency stop is released，Emergency stop IO output closed on the receiver，All functions of the handwheel are restored。
②Screen display：
③Custom button：
4Custom buttons，Each button corresponds to an IO output point on the receiver，Connect to the system via IO-LINK。Generally, the ~ button is set as a high-speed button。
④Axis selection switch：
Switching the axis selection switch can switch the moving axis controlled by the handwheel。
⑤Shortcut button：
Press the shortcut button +，Machine moving forward，Press the shortcut button -，Machine moves in negative direction，Can replace the hand wheel to move the machine。
⑥Enable button：

Press and hold either enable button on either side，It is effective only by shaking the pulse encoder。 And the 2 sets of enabled IO outputs on the receiver are turned on，Release the enable button，Enable IO output disconnection。

⑦Magnification switch：

Switching the magnification switch can switch the magnification controlled by the hand wheel.。

⑧Pulse encoder：

Press and hold the enable button，Shaking pulse encoder，Send a pulse signal，Control the machine shaft movement。

⑨Power switch：
Handwheel start button。



Product installation steps：
1.Install the receiver in the electric cabinet through the snap-on on the back，Or install it in the electrical cabinet through the screw holes at the four corners of the receiver.。
2.Refer to our receiver wiring diagram，Compare your on-site equipment，Connect the device through a cable and a receiver。
3.After the receiver is fixed，The antenna equipped with the receiver must be connected，And install the outer end of the antenna or place it outside the electric cabinet，It is recommended to place the signal on the top of the electric cabinet.，It is not allowed to disconnect the antenna，Or place the antenna inside the electric cabinet，It may cause the signal to be unusable。

4.Finally turn on the handwheel power switch，You can operate the handwheel remote control machine。

Receiver installation size：

Receiver Wiring Reference Diagram：

1.Please at room temperature and pressure，Used in dry environments，Extend service life；
2.Please avoid getting wet in the rain、Used in abnormal environments such as blisters，Extend service life；
3.Please keep the handwheel clean，Extend service life；
4.Please avoid squeezing、Fall、Bumping, etc.，Prevent precision accessories inside the handwheel from damage or accuracy errors；
5.Not used for a long time，Please store the handwheel in a clean and safe place；
6.Pay attention to moisture-proof and shock-proof during storage and transportation。
1.Please read the instructions for use in detail before use，Non-professional personnel are prohibited；
2.Please charge in time when the battery is too low，Avoid errors caused by insufficient power, causing the handwheel to be unable to operate；
3.If repair is required，Please contact the manufacturer，If damage caused by self-repair，The manufacturer will not provide a warranty。
]]> Crawler rope saw machine-automatic wireless remote control DH12S-LD https://www.wixhc.com/cn/product/%e5%b1%a5%e5%b8%a6%e7%bb%b3%e9%94%af%e6%9c%ba-%e8%87%aa%e5%8a%a8%e6%97%a0%e7%ba%bf%e9%81%a5%e6%8e%a7%e5%99%a8-dh12s-ld Fri, 17 Nov 2023 05:53:18 +0000 https://www.wixhc.com/cn/?post_type=product&p=97249

model：DH12S-LD Adaptive equipment：Crawler rope sawing machine

Remark：Three types of antennas can be selected，The default suction cup antenna is equipped with standard

Large motor speed：S1：0-50
Small motor speed：S2：0-50
Automatic cutting motor maximum speed limit：F：0-30(The parameters are adjustable)
Automatic cutting maximum current：Ic：0-35(The parameters are adjustable)
Linear deviation correction value：Df：-99-99(1 unit is approximately 0.02V)

Low pressure：The battery of the remote control is too low，Please replace the battery

Fall out of the internet：Wireless signal interruption，Please check the receiver power supply，Power on again，Restart the remote control

1、Remote control turned on

The receiver is powered on，The RF-LED light on the receiver starts to flash；Two No. 5 batteries installed on the remote control，Turn on the power switch，Display display motor speed，It means the startup is successful。

2、Large motor and speed regulation
Turn the "Forward/Reverse" switch to forward，The receiver's large motor turns on，The display displays forward rotation；
Turn the "Forward/Reverse" switch to reverse，Receiver large motor reversal on，Display display inversion；

Rotate the "Large Motor Speed ​​Regulation" knob，It can adjust the output voltage of the receiver large motor speed regulation 0-10V；

3、Small motor and speed regulation

Turn the "Forward/Reverse" switch to forward，Receiver Revolver Progress and Right Progress Open，Display forward

Turn the "Forward/Reverse" switch to the back，Receiver reversal and right wheel reversal open，Display back
In manual mode：Rotate the "Small Motor Speed ​​Regulation" knob，At the same time, adjust the output voltage of the receiver's left wheel right wheel speed regulation 0-10V；

4、Turn left and right

Turn the "Left/Right" switch to the left，Receiver right wheel advances to open，The display display turns left

Turn the "Left/Right" switch to the right，Receiver revolver advance opens，The display display turns right
5、Turning in place
In manual mode：
Turn left in place：Press and hold the Enable button，Turn the "Left/Right" switch to the left，Receiver's reversal and right wheel advance open，Start turning left in place；

Turn right in place：Press and hold the Enable button，Turn the "Left/Right" switch to the right，The receptacle's revolver advances and the right-wheel backs opens，Start turning right in place；

6、Small motor speed limit adjustment

In automatic mode：Press and hold the Enable button，Rotate the "Small Motor Speed ​​Regulation" to adjust the maximum speed of the small motor during automatic cutting；

7、Automatic cutting
first step，Start the large motor；
Step 2，Switch the mode switch to "auto"；
Step 3，Start the small motor，The screen display enters "Cutting Automatic"，Indicates that the automatic cutting mode has been entered；

 

8、Straight line correction
When the left and right motor is moving forward and backward，There is a difference in the left and right speeds，Straight-line walking is offset，The linear deviation correction function of the remote control can be used，Fine-tune the speed of left and right wheels；
Principle of correction：Through bias correction function，Fine-tune revolver speed，To achieve the same speed as the right wheel，Realize the synchronization of left and right wheel speeds，Eliminate offsets；
Correction operation method：In manual mode，Press and hold the Enable button，Rotate "small motor speed regulation"；
Rotate clockwise，Increase the revolver speed voltage，Increased deviation correction value of the display screen；
Rotate counterclockwise，Reduce the revolver speed voltage，The display deviation correction value is reduced；

Correction range：Correction value -90 to 90；1The bias correction voltage of each deviation correction unit is approximately 0.02V；

9、Parameter menu (user prohibits private modification)
Some functions of the remote control can be adjusted through parameters，In manual mode，When the speed of small motor S2 is 10，
Forward/reverse switch is bent up 3 times in a row，Then break it 3 times in a row，Enter the parameter menu；
Exit the Parameters Menu：Choose to save or not，Then press the enable button to confirm exit；
Maximum current:Working current of the cutting motor，The cutting current is 80% of this current；
Speed ​​regulation parameters:Automatic cutting control parameters，Default 800，Modification is prohibited；
Deceleration parameters:Automatic cutting control parameters，When the cutting current change value exceeds this value，Start slowing down
Acceleration a1: Automatic cutting control parameters，When the cutting current is lower than the set cutting current，Speed ​​up slowly；
Deceleration a2: Automatic cutting control parameters，When the cutting current is higher than the set cutting current，Slow speed；
Automatic knife collection:invalid；
Start self-locking：0，Don't lock yourself；1，Self-locking. Press the enable key + forward and reverse to take effect，And lock it；
Maximum walking:Minimum motor speed；
Cutting current:Set the maximum current value of the main motor for automatic cutting，The feedback current exceeds this value，Start slowing down；
Default speed limit:When powering on，Default maximum speed for automatic cutting speed；
Automatic mode:0，Automatic switch is automatic control；1，Automatic switch control automatic IO output point；
Speed ​​limit offset:When cutting automatically,Maximum speed of small motor；
Maximum host:大电机最大速度.

 

Receiver operating power supply DC24V/1A (independent power supply)
Receiver output point load AC0-250V/3A DC0-30V/5A
Receiver speed regulation output voltage
DC0-10V
]]> Multi-switch industrial wireless remote control DH05 https://www.wixhc.com/cn/product/%e5%a4%9a%e5%bc%80%e5%85%b3%e9%87%8f%e5%b7%a5%e4%b8%9a%e6%97%a0%e7%ba%bf%e9%81%a5%e6%8e%a7%e5%99%a8dh05 Fri, 22 Apr 2022 07:25:30 +0000 https://www.wixhc.com/cn/?post_type=product&p=55904

]]> Floor grinder industrial automation control remote control DH22-2R-7K https://www.wixhc.com/cn/product/%e5%9c%b0%e5%9d%aa%e7%a0%94%e7%a3%a8%e6%9c%ba%e5%b7%a5%e4%b8%9a%e8%87%aa%e5%8a%a8%e5%8c%96%e6%8e%a7%e5%88%b6%e9%81%a5%e6%8e%a7%e5%99%a8dh22-2r-7k Tue, 19 Apr 2022 01:33:16 +0000 https://www.wixhc.com/cn/?post_type=product&p=55671

]]> Roller frame, wire saw cutting, multi-function wireless industrial remote control, DH22 https://www.wixhc.com/cn/product/%e6%bb%9a%e8%bd%ae%e6%9e%b6-%e7%bb%b3%e9%94%af%e5%88%87%e5%89%b2-%e5%a4%9a%e5%8a%9f%e8%83%bd%e6%97%a0%e7%ba%bf%e5%b7%a5%e4%b8%9a%e9%81%a5%e6%8e%a7%e5%99%a8-dh22 Fri, 18 Mar 2022 07:56:15 +0000 https://www.wixhc.com/cn/?post_type=product&p=53346

]]> Roller frame, wire saw cutting, multi-functional industrial remote control, DH02S-AT https://www.wixhc.com/cn/product/%e6%bb%9a%e8%bd%ae%e6%9e%b6-%e7%bb%b3%e9%94%af%e5%88%87%e5%89%b2-%e5%a4%9a%e5%8a%9f%e8%83%bd%e5%b7%a5%e4%b8%9a%e9%81%a5%e6%8e%a7%e5%99%a8-dh02s-at Wed, 09 Sep 2020 07:37:24 +0000 https://www.wixhc.com/cn/?post_type=product&p=13849

 

 

 

 

]]>