Fanako special handwheel XWGP–Ets-Fanuc

Wireless electronic handwheel is used for manual guidance of CNC machine tools、position、Strike operation。This product uses wireless transmission technology，Eliminates traditional spring wire connections，Reduce equipment failures caused by cables，Eliminate cable drag，Disadvantages such as oil stains，More convenient to operate。This model of wireless electronic handwheel is a special handwheel for Fanak system，IO-LINK protocol realizes real-time display of Fanak system coordinates on the handwheel screen，And through the IO-LINK protocol，Select the axis directly、magnification、Button signal access system，Reduce wiring。

1.Using 433MHZ wireless communication technology，Wireless operating distance 40 meters；

2.Use automatic frequency hopping function，Use 32 sets of wireless remote controls at the same time，Do not affect each other；

3.Support emergency stop button，Switching quantity IO signal output，Connection to system via IO wiring；

4.Supports 4 custom buttons，Switching IO signal，Output signals to the system through IO-LINK protocol；

5.Supports quick moving buttons + and buttons-，Pressing and holding the button can move the machine instead of the handwheel；

6.Supports 6-axis control，Switching IO signal，Output signals to the system through IO-LINK protocol；

7.Supports 3-speed multiplier control，Switching IO signal，Output signals to the system through IO-LINK protocol；

8.Support enable button function，Connection to system via IO wiring，Control encoder enables；

9.Support pulse encoder，100Pulse/turn，Access the MPG handwheel interface of the system by outputting AB coded signal；

Comment：

②Screen display：

③Custom buttons：

4Custom buttons，Each button corresponds to an IO output point on the receiver，Connect to the system via IO-LINK。Generally, set the ~ button to a high-speed button。

④Axis selection switch：

Switching the axis selection switch can switch the moving axis controlled by the handwheel。

⑤ Quick button：

Press the shortcut button +，The machine moves forward，按下快捷按钮-，机器负向移动，可以代替摇手轮移动机器。

⑥使能按钮：

按住两侧任意一个使能按钮，摇动脉冲编码器才有效。 并且接收器上的2组使能IO输出导通，松开使能按钮，使能IO输出断开。

⑦倍率开关：

切换倍率开关可以切换手轮控制的倍率。

⑧脉冲编码器：

按住使能按钮，Shaking pulse encoder，Send a pulse signal，Control the machine shaft movement。

⑨Power switch：

Handwheel power-on button。

Product installation steps：
1.Install the receiver in the electric cabinet through the snap-on on the back，Or install it in the electrical cabinet through the screw holes at the four corners of the receiver.。

2.Refer to our receiver wiring diagram，Compare your on-site equipment，Connect the device through a cable and a receiver。

3.接收器固定好后，必须将接收器配备的天线接好，并且将天线外端安装或者放置在电柜外部，建议放在电柜顶部信号效果最好，禁止将天线不接，或者将天线放在电柜内部，可能会导致信号无法使用。

4.最后打开手轮电源开关，就可以进行手轮遥控机器操作了。

1.Please keep it at normal temperature and pressure，Use in dry environment，Extend service life；

2.Please avoid getting wet in the rain、Used in abnormal environments such as blisters，Extend service life；

3.Please keep the handwheel clean，Extend service life；

4.Please avoid squeezing、Fall、Bumping, etc.，Prevent precision accessories inside the handwheel from damage or accuracy errors；

5.Not used for a long time，Please store the handwheel in a clean and safe place；

6.Pay attention to moisture-proof and shock-proof during storage and transportation。

1.Please read the instructions carefully before use，Operation by non-professionals is prohibited；

2.Please charge it in time when the battery is too low，Avoid errors caused by insufficient power, causing the handwheel to be unable to operate；

3.Need repair，Please contact the manufacturer，If the damage is caused by self-repair，The manufacturer will not provide warranty。