LXWGP-ETS-SIEMENS wired electronic handwheel
Description
电子手轮是用于数控机床手动引导、position、Strike operation。This model of electronic handwheel is a Siemens wired electronic handwheel with real display.，The handwheel is connected to the X130 interface of the Siemens system through a network cable.，Read the system coordinates and display them to the LCD display of the handwheel through S7 protocol communication.，And the handwheel control system axis selection can be made through communication.、magnification、Button and other signals。
1.采用6芯航空插头线缆连接，手轮线缆长度10米。
2.手轮屏幕可以显示系统工件坐标、机械坐标、进给速度、轴选、倍率等信息。
3.Support emergency stop button，Switching quantity IO signal output，手轮关机急停依然有效。
4.支持6个自定义按钮，开关量IO信号，可以通过IO接线或通信输出信号给系统。
5.支持6或8轴控制，开关量IO信号，可以通过IO接线或通信输出信号给系统。
6.支持3或4档倍率控制，开关量IO信号，可以通过IO接线或通信输出信号给系统。
7.Support pulse encoder，100Pulse/Circle，可以通过AB脉冲接线输出信号给系统。
8.Support Siemens S7 protocol，Support Siemens 828D、840DSL、ONE and other model systems。
| 手轮工作电源电压 | DC24V/1A |
| Receiver power supply voltage | DC24V/1A |
| 接收器IO输出负载范围 |
DC24V
|
| 手轮端线缆长度 |
10m
|
| 接收器端线缆长度 |
1m
|
| 接收器端网线长度 |
3m
|
| Operating temperature |
-25℃<X<55℃
|
| Anti-fall height |
1m
|
| Customize the number of buttons | 6个 |
| Product size | 233*90.7*77.4（mm） |
Comments：
①急停按钮：
Press the emergency stop button，Two groups of emergency stop IO outputs on the receiver are disconnected，And all functions of the handwheel are invalid。
After the emergency stop is released，Emergency stop IO output closed on the receiver，All functions of the handwheel are restored。
②屏幕显示：
PLC：0000代表网线没有连通，PLC：1010代表网线和PLC系统连接成功，
PLC：1110代表手轮写入系统数据成功，PLC：0001代表连接电脑成功。
③自定义按钮：
6Custom buttons，Each button corresponds to an IO output point on the receiver，也通过通信与系统连接。
④轴选开关：
Switching the axis selection switch can switch the moving axis controlled by the handwheel。
⑤使能按钮：
按住两侧任意一个使能按钮，摇动脉冲编码器才有效。 并且接收器上的2组使能IO输出导通，Release the enable button，Enable IO output disconnection。
⑥倍率开关：
切换倍率开关可以切换手轮控制的倍率。
⑦脉冲编码器：
Press and hold the enable button，Shaking pulse encoder，Send a pulse signal，Control the machine shaft movement。
⑧手轮线缆：
手轮和接收器连接的线缆，航空插头，用于手轮供电和通信。
6.1Product installation steps
1.将接收器通过四个角的螺丝孔将其安装在电柜里。
2.Refer to our receiver wiring diagram，Compare your on-site equipment，将设备通过线缆和接收器
连接，用网线把接收器和系统的X130接口连接好。
3.After the receiver is fixed，将航空插头底座安装在面板的手轮开孔位置，底座另一
端线排插在接收器上的手轮接口处。然后将手轮端线缆航空插头插入底座，拧紧
固定装置。
6.2Receiver installation size
6.3航空插头安装尺寸
6.4Receiver Wiring Reference Diagram
6.2Receiver installation size
6.3航空插头安装尺寸
6.4Receiver Wiring Reference Diagram
1.The receiver is powered on，The receiver operating light is on，用网线将接收器和电脑连接，设置电脑的固定IP地址，使用网络配置工具软件对手轮功能进行网络参数设置，具体设置
方法参考《LXWGP-ETS有线手轮的使用说明》。
2.接收器设置完成之后，系统需要编程PLC程序，具体请参考《LXWGP-ETS不同西门子数控系统的设置方法》以及PLC程序例程资料。
3.以上设置完成之后，将接收器拿到机器电柜安装好，网线从电脑拔出插到系统的X130接口上，接收器电源和脉冲线插好。
4.The machine is powered，The receiver is powered on，The receiver operating light is on，打开手轮电源开关，手轮屏幕开机，屏幕显示PLC:1010，代表手轮和系统通信成功。
5.选中轴选：Switch axle selection switch，Select the axis you want to operate。
6.Select the multiplier：Switch the magnification switch，Select the multiplier you need。
7.Move the axis：Press and hold the enable button，Select the axis and switch，Select the multiplier switch，Then turn the pulse encoder，Turn clockwise forward movement axis，Turn the negative movement axis counterclockwise。
8.Press and hold any custom button，The corresponding button IO output of the receiver is turned on，Release button output close。
9.Press the emergency stop button，The receiver disconnects the emergency stop IO output，Handwheel function fails，Release the emergency stop button，Emergency stop IO output closed，Handwheel function recovery。
| Fault situation | Possible Cause |
Troubleshooting Methods
|
|
|
Troubleshooting Methods
|
1.手轮和接收器之间的航空线缆是否正确可靠连接
2.接收器电源电压是否足够
3.Handwheel failure
|
1.检查手轮和接收器之间的航空线缆的连接情况
2.检查接收器输入电源
3.Contact the manufacturer to return to the factory for maintenance
|
|
| 手轮操作无反应 |
1.接收器和系统的网线是否连接
2.系统PLC程序是否写好
3.接收器配置是否设置正确
4.手轮显示屏485通信图标是否显示失败
5.When operating the handwheel，需要按住两侧的使能按钮
6.急停按钮是否释放
|
1.检查接收器和系统X130网口是否用网线连接
2.检查确认系统PLC是否按照我们提供的参考资料写好
3.检查确认接收器是否参考我们的资料和提供的工具软件，正确的设置了接收器的网络参数和DB地址等
4.检查手轮和接收器之间的
6芯绿色插座，其中的两根通信线：485-A和485-B，是否正确并牢固连接，是否存在断路的情况
|
|
|
After the receiver is powered on，接收器上工作灯不亮
|
1.Power supply abnormality
2.Power wiring error
3.Receiver failure
|
1.Check if the power supply has voltage，
Does the voltage meet the requirements
2.Check whether the positive and negative poles of the power supply are connected in reverse
3.Return to factory maintenance
|
1.Please at room temperature and pressure，Used in dry environments，Extend service life。
2.Please avoid getting wet in the rain、Used in abnormal environments such as blisters，Extend service life。
3.Please keep the handwheel clean，Extend service life。
4.Please avoid squeezing、Fall、Bumping, etc.，Prevent precision accessories inside the handwheel from damage or accuracy errors。
5.Not used for a long time，Please store the handwheel in a clean and safe place。
6.Pay attention to moisture-proof and shock-proof during storage and transportation。
1.Please read the instructions for use in detail before use，Non-professional personnel are prohibited。
2.手轮出现任何非正常情况后，请立即停止使用，并且排查故障，在故障排除前，禁止再使用故障手轮，避免因手轮未知故障而发生安全事故；
3.If repair is required，Please contact the manufacturer，If damage caused by self-repair，The manufacturer will not provide a warranty。
