绳锯机自动切割无线遥控器 DH12S-P6S

Description

model：DH12S-P6S 适配设备：绳锯/片锯机

备注：三种天线可以三选一，默认标配吸盘天线

主电机速度：主：0-50
行走电机速度：行：0-50
自动切割行走电机最高限速：speed：0-30(The parameters are adjustable)
Automatic cutting main motor set current：set up：28(The parameters are adjustable)
Swing arm motor speed：put：0-50

Low pressure：The battery of the remote control is too low，Please replace the battery

Fall out of the internet：Wireless signal interruption，Please check the receiver power supply，Power on again，Restart the remote control

1、Remote control turned on

The receiver is powered on，The D2 power supply light on the receiver is always on，D1 signal light starts to flash；Two No. 5 batteries installed on the remote control，Turn on the power switch，显示屏显示电机速度，表示开机成功。

2、主电机和调速
按住“调速使能”，将“正转/反转”开关扳到正转，接收器主电机正转打开；

按住“调速使能”，将“正转/反转”开关扳到反转，接收器主电机反转打开；

直接将开关扳到中间或者反向，主电机立即停止，无需按调速使能；

旋转“大电机”旋钮，The speed regulation voltage of the receiver main motor inverter can be adjusted 0-10V；
3、Walking motor

按住“调速使能”，Turn the "Forward/Reverse" switch to forward or backward，The walking motor will move at a high speed of 50；

4、Swing arm motor and speed regulation

Turn the "Swing Arm/Return" switch to the swing arm or back，The swing arm motor of the receiver starts；Then turn the "speed adjustment" knob，Can adjust the speed of the swing arm motor；

按住“调速使能”，再扳动“摆臂/后退”开关，摆臂电机将以高速50移动；

5、行走电机限速调整

按住“调速使能”按钮，旋转“速度调节”可以调整自动切割时行走电机的最大限速；

6、自动切割

第一步，启动主电机；第二步，调整行走电机的最大限速；第三步，将“前进/后退”开关扳动前进或者后退，Enter automatic cutting mode；

7、Parameter settings (users prohibit private modification)

Enter the parameter menu：In manual mode，When the main motor speed is 0，Forward/reverse switch is bent up 3 times in a row，Then break it 3 times in a row，Enter the parameter menu；

Exit the Parameters Menu：Speed adjustment knob page turn，Choose to save or not save，Press the enable button to confirm；

Rated current:Maximum value of main motor current，Unit Ampere；

Speed regulation parameters:Automatic cutting control parameters，Default 800，Unit milliseconds，Modification is prohibited；

Deceleration parameters:When the cutting current change value exceeds this value，Start to decelerate rapidly，Unit Ampere；

Acceleration a1:When the cutting current is lower than the set cutting current，The speed value of each acceleration of the walking motor；

Deceleration a2: When the cutting current is higher than the set cutting current，The speed value of the walking motor reduces each time it decelerates；

Swing arm current:default value，Modification is prohibited；
Stop time:自动模式电流超载停机后，隔一段时间再次检测电流，如果小于设定电流，自动启动行走电机；单位秒，default value，Modification is prohibited；

最大电流:主电机反馈电流的范围，Unit Ampere；

最大主机:遥控器主电机调速显示范围；

最大行走:无效参数；

限速偏移:自动切割时,遥控器显示屏行走电机限速=此参数的50%；

加灵敏度:When the feedback current of the main motor increases，The value increased each time exceeds this value，Walking motor acceleration；

Reduce sensitivity:Main motor feedback current decreases，The value reduced each time exceeds this value，Walking motor slows down；

Sensitivity offset:The offset increase of the adding and subtracting sensitivity parameters；
Set current:自动切割，The threshold for feedback current of main motor，More than this value，The walking motor starts to slow down；Below this value，The walking motor starts to accelerate；Unit Ampere；

空走退出:自动模式开始时，如果主电机反馈电流小于此值，则处于空走模式，大于此值，则退出空走模式，进入切割模式，Unit Ampere；

空载电流:自动模式开始时，如果主电机反馈电流小于此值，则处于空载模式，大于此值，则退出空载模式，进入切割模式，Unit Ampere；

摆臂速度:摆臂电机开机初始速度；

切割模式:片锯和绳锯两种模式切换，切换后参数也对应切换；片锯模式下，遥控器显示屏增加摆臂电机，绳锯模式则没有摆臂电机；

去抖时间:主电机反馈电流超过停止电流时，将持续检测反馈电流，去抖时间就是这个持续检测的时长，超过这个时间，检测主电机电流依然超过停止电流，行走电机将停止；反之则行走电机会继续前进；

停止电流:The feedback current of the main motor exceeds this value，The walking motor will stop；Unit Ampere；

Offset default:The initial value of the speed limit of the traveling motor when the remote control is turned on = 50% of this value；

Receiver operating power supply	DC24V/1A (independent power supply)
Receiver output point load	AC0-250V/3A DC0-30V/5A
Receiver speed regulation output voltage	DC0-10V