无线电子手轮/电子手轮/手轮/CNC电子手轮 无线电子手轮XWGP-ETS-FANUC
适用于法那科数控系统.
Fanako special handwheel XWGP–Ets-Fanuc
Description
无线电子手轮是用于数控机床手动引导、position、Strike operation。This product uses wireless transmission technology，Eliminates traditional spring wire connections，Reduce equipment failures caused by cables，Free cable drag，Disadvantages such as oil stains，More convenient operation。该型号无线电子手轮是发那科系统专用手轮，通过IO-LINK协议实现发那科系统坐标实时在手轮屏幕显示，并且通过IO-LINK协议，直接把轴选、倍率、按钮信号接入系统，减少接线。
1.Adopt 433MHZ wireless communication technology，Wireless operation distance 40 meters；
2.Adopt automatic frequency hopping function，Use 32 sets of wireless remote controls at the same time，No effect on each other；
3.Support emergency stop button，Switching quantity IO signal output，通过IO接线和系统连接；
4.支持4个自定义按钮，开关量IO信号，通过IO-LINK协议输出信号给系统；
5.支持快捷移动按钮+和按钮-，按住按钮可以代替摇手轮移动机器；
6.支持6轴控制，开关量IO信号，通过IO-LINK协议输出信号给系统；
7.Supports 3-speed multiplier control，开关量IO信号，通过IO-LINK协议输出信号给系统；
8.Support enable button function，通过IO接线和系统连接，同时控制编码器使能；
9.Support pulse encoder，100脉冲/圈，通过输出AB编码信号接入系统MPG 手轮接口；
Comments：
Comments：
①急停按钮：
Press the emergency stop button，Two groups of emergency stop IO outputs on the receiver are disconnected，And all functions of the handwheel are invalid。释放急停后，Emergency stop IO output closed on the receiver，All functions of the handwheel are restored。
②屏幕显示：
③自定义按钮：
4Custom buttons，Each button corresponds to an IO output point on the receiver，通过IO-LINK与系统连接。一般把~按钮设置为高速按钮。
④轴选开关：
Switching the axis selection switch can switch the moving axis controlled by the handwheel。
⑤快捷按钮：
按下快捷按钮+，机器正向移动，按下快捷按钮-，机器负向移动，可以代替摇手轮移动机器。
⑥使能按钮：
按住两侧任意一个使能按钮，摇动脉冲编码器才有效。 并且接收器上的2组使能IO输出导通，Release the enable button，Enable IO output disconnection。
⑦倍率开关：
切换倍率开关可以切换手轮控制的倍率。
⑧脉冲编码器：
Press and hold the enable button，Shaking pulse encoder，Send a pulse signal，Control the machine shaft movement。
⑨电源开关：
手轮开机按钮。
Product installation steps：
1.Install the receiver in the electric cabinet through the snap-on on the back，Or install it in the electrical cabinet through the screw holes at the four corners of the receiver.。
1.Install the receiver in the electric cabinet through the snap-on on the back，Or install it in the electrical cabinet through the screw holes at the four corners of the receiver.。
2.Refer to our receiver wiring diagram，Compare your on-site equipment，Connect the device through a cable and a receiver。
3.After the receiver is fixed，The antenna equipped with the receiver must be connected，And install the outer end of the antenna or place it outside the electric cabinet，It is recommended to place the signal on the top of the electric cabinet.，It is not allowed to disconnect the antenna，Or place the antenna inside the electric cabinet，It may cause the signal to be unusable。
4.Finally turn on the handwheel power switch，You can operate the handwheel remote control machine。
Receiver installation size：
Receiver Wiring Reference Diagram：
1.Please at room temperature and pressure，Used in dry environments，Extend service life；
2.Please avoid getting wet in the rain、Used in abnormal environments such as blisters，Extend service life；
3.Please keep the handwheel clean，Extend service life；
4.Please avoid squeezing、Fall、Bumping, etc.，Prevent precision accessories inside the handwheel from damage or accuracy errors；
5.Not used for a long time，Please store the handwheel in a clean and safe place；
6.Pay attention to moisture-proof and shock-proof during storage and transportation。
1.Please read the instructions for use in detail before use，Non-professional personnel are prohibited；
2.电量过低时请及时充电，Avoid errors caused by insufficient power, causing the handwheel to be unable to operate；
3.If repair is required，Please contact the manufacturer，If damage caused by self-repair，The manufacturer will not provide a warranty。
