Crawler rope saw machine-automatic wireless remote control DH12S-LD

Description

model：DH12S-LD Adaptive equipment：Crawler rope sawing machine

Remark：Three types of antennas can be selected，The default suction cup antenna is equipped with standard

Large motor speed：S1：0-50

Small motor speed：S2：0-50

Automatic cutting motor maximum speed limit：F：0-30(The parameters are adjustable)

Automatic cutting maximum current：Ic：0-35(The parameters are adjustable)

Linear deviation correction value：Df：-99-99(1 unit is approximately 0.02V)

Low pressure：The battery of the remote control is too low，Please replace the battery

Fall out of the internet：Wireless signal interruption，Please check the receiver power supply，Power on again，Restart the remote control

1、Remote control turned on

The receiver is powered on，The RF-LED light on the receiver starts to flash；Two No. 5 batteries installed on the remote control，Turn on the power switch，Display display motor speed，It means the startup is successful。

2、Large motor and speed regulation

Turn the "Forward/Reverse" switch to forward，The receiver's large motor turns on，The display displays forward rotation

；
Turn the "Forward/Reverse" switch to reverse，Receiver large motor reversal on，Display display inversion

；

Rotate the "Large Motor Speed Regulation" knob，It can adjust the output voltage of the receiver large motor speed regulation 0-10V；

3、Small motor and speed regulation

Turn the "Forward/Reverse" switch to forward，Receiver Revolver Progress and Right Progress Open，Display forward

Turn the "Forward/Reverse" switch to the back，Receiver reversal and right wheel reversal open，Display back

In manual mode：Rotate the "Small Motor Speed Regulation" knob，At the same time, adjust the output voltage of the receiver's left wheel right wheel speed regulation 0-10V；

4、Turn left and right

Turn the "Left/Right" switch to the left，Receiver right wheel advances to open，The display display turns left

Turn the "Left/Right" switch to the right，Receiver revolver advance opens，The display display turns right

5、Turning in place

In manual mode：

Turn left in place：Press and hold the Enable button，Turn the "Left/Right" switch to the left，Receiver's reversal and right wheel advance open，Start turning left in place；

Turn right in place：Press and hold the Enable button，Turn the "Left/Right" switch to the right，The receptacle's revolver advances and the right-wheel backs opens，Start turning right in place；

6、Small motor speed limit adjustment

In automatic mode：Press and hold the Enable button，Rotate the "Small Motor Speed Regulation" to adjust the maximum speed of the small motor during automatic cutting；

7、Automatic cutting

first step，Start the large motor；
Step 2，Switch the mode switch to "auto"；
Step 3，Start the small motor，The screen display enters "Cutting Automatic"，Indicates that the automatic cutting mode has been entered；

8、Straight line correction

When the left and right motor is moving forward and backward，There is a difference in the left and right speeds，Straight-line walking is offset，The linear deviation correction function of the remote control can be used，Fine-tune the speed of left and right wheels；

Principle of correction：Through bias correction function，Fine-tune revolver speed，To achieve the same speed as the right wheel，Realize the synchronization of left and right wheel speeds，Eliminate offsets；

Correction operation method：In manual mode，Press and hold the Enable button，Rotate "small motor speed regulation"；

Rotate clockwise，Increase the revolver speed voltage，Increased deviation correction value of the display screen；

Rotate counterclockwise，Reduce the revolver speed voltage，The display deviation correction value is reduced；

Correction range：Correction value -90 to 90；1The bias correction voltage of each deviation correction unit is approximately 0.02V；

9、Parameter menu (user prohibits private modification)

Some functions of the remote control can be adjusted through parameters，In manual mode，When the speed of small motor S2 is 10，

Forward/reverse switch is bent up 3 times in a row，Then break it 3 times in a row，Enter the parameter menu；

Exit the Parameters Menu：Choose to save or not，Then press the enable button to confirm exit；

Maximum current:Working current of the cutting motor，The cutting current is 80% of this current；

Speed regulation parameters:Automatic cutting control parameters，Default 800，Modification is prohibited；

Deceleration parameters:Automatic cutting control parameters，When the cutting current change value exceeds this value，Start slowing down

Acceleration a1: Automatic cutting control parameters，When the cutting current is lower than the set cutting current，Speed up slowly；

Deceleration a2: Automatic cutting control parameters，When the cutting current is higher than the set cutting current，Slow speed；

Automatic knife collection:invalid；

Start self-locking：0，Don't lock yourself；1，Self-locking. Press the enable key + forward and reverse to take effect，And lock it；

Maximum walking:Minimum motor speed；

Cutting current:Set the maximum current value of the main motor for automatic cutting，The feedback current exceeds this value，Start slowing down；

Default speed limit:When powering on，Default maximum speed for automatic cutting speed；

Automatic mode:0，Automatic switch is automatic control；1，Automatic switch control automatic IO output point；

Speed limit offset:When cutting automatically,Maximum speed of small motor；

Maximum host:Large motor maximum speed.

Receiver operating power supply	DC24V/1A (independent power supply)
Receiver output point load	AC0-250V/3A DC0-30V/5A
Receiver speed regulation output voltage	DC0-10V