Automatic cutting wireless remote control of wire saw machine DH12S-P6S

Description

model：DH12S-P6S adapter equipment：Wire saw/blade saw machine

Remark：Three types of antennas can be selected，The default suction cup antenna is equipped with standard

Main motor speed：host：0-50
Travel motor speed：OK：0-50
Automatic cutting travel motor maximum speed limit：speed：0-30(The parameters are adjustable)
Automatic cutting main motor set current：set up：28(The parameters are adjustable)
Swing arm motor speed：put：0-50

Low pressure：The battery of the remote control is too low，Please replace the battery

Fall out of the internet：Wireless signal interruption，Please check the receiver power supply，Power on again，Restart the remote control

1、Remote control turned on

The receiver is powered on，The D2 power supply light on the receiver is always on，D1 signal light starts to flash；Two No. 5 batteries installed on the remote control，Turn on the power switch，Display display motor speed，It means the startup is successful。

2、Main motor and speed regulation
Press and hold "Speed control enable"，Turn the "Forward/Reverse" switch to forward，The main motor of the receiver rotates forward and turns on；

Press and hold "Speed control enable"，Turn the "Forward/Reverse" switch to reverse，Receiver main motor reverses and turns on；

Simply move the switch to the middle or reverse，The main motor stops immediately，No need to press speed control to enable；

Turn the "Big Motor" knob，The speed regulation voltage of the receiver main motor inverter can be adjusted 0-10V；
3、Walking motor

Press and hold "Speed control enable"，Turn the "Forward/Reverse" switch to forward or backward，The walking motor will move at a high speed of 50；

4、Swing arm motor and speed regulation

Turn the "Swing Arm/Return" switch to the swing arm or back，The swing arm motor of the receiver starts；Then turn the "speed adjustment" knob，Can adjust the speed of the swing arm motor；

Press and hold "Speed control enable"，Then flip the "swing arm/reverse" switch，The swing arm motor will move at a high speed of 50；

5、Travel motor speed limit adjustment

Press and hold the "Speed Enable" button，Turn "Speed Adjustment" to adjust the maximum speed limit of the traveling motor during automatic cutting.；

6、Automatic cutting

first step，Start the main motor；Step 2，Adjust the maximum speed limit of the traveling motor；Step 3，Turn the "forward/reverse" switch to move forward or backward，Enter automatic cutting mode；

7、Parameter settings (users prohibit private modification)

Enter the parameter menu：In manual mode，When the main motor speed is 0，Forward/reverse switch is bent up 3 times in a row，Then break it 3 times in a row，Enter the parameter menu；

Exit the Parameters Menu：Speed adjustment knob page turn，Choose to save or not save，Press the enable button to confirm；

Rated current:Maximum value of main motor current，Unit Ampere；

Speed regulation parameters:Automatic cutting control parameters，Default 800，Unit milliseconds，Modification is prohibited；

Deceleration parameters:When the cutting current change value exceeds this value，Start to decelerate rapidly，Unit Ampere；

Acceleration a1:When the cutting current is lower than the set cutting current，The speed value of each acceleration of the walking motor；

Deceleration a2: When the cutting current is higher than the set cutting current，The speed value of the walking motor reduces each time it decelerates；

Swing arm current:default value，Modification is prohibited；
Stop time:After shutdown due to current overload in automatic mode，Check the current again after a period of time，If it is less than the set current，Automatically start the walking motor；Unit second，default value，Modification is prohibited；

Maximum current:Main motor feedback current range，Unit Ampere；

Maximum host:Remote control main motor speed display range；

Maximum walking:Invalid parameter；

Speed limit offset:When cutting automatically,Remote control display walking motor speed limit = 50% of this parameter；

Add sensitivity:When the feedback current of the main motor increases，The value increased each time exceeds this value，Walking motor acceleration；

Reduce sensitivity:Main motor feedback current decreases，The value reduced each time exceeds this value，Walking motor slows down；

Sensitivity offset:The offset increase of the adding and subtracting sensitivity parameters；
Set current:Automatic cutting，The threshold for feedback current of main motor，More than this value，The walking motor starts to slow down；Below this value，The walking motor starts to accelerate；Unit Ampere；

Empty exit:When automatic mode starts，If the main motor feedback current is less than this value，is in idling mode，greater than this value，then exit idling mode，Enter cutting mode，Unit Ampere；

No-load current:When automatic mode starts，If the main motor feedback current is less than this value，is in no-load mode，greater than this value，then exit the no-load mode，Enter cutting mode，Unit Ampere；

Swing arm speed:Swing arm motor startup speed；

cutting mode:Switch between blade saw and wire saw modes，After switching, the parameters will also switch accordingly.；In blade saw mode，A swing arm motor is added to the remote control display，The wire saw mode does not have a swing arm motor.；

Debounce time:When the main motor feedback current exceeds the stop current，Will continuously detect the feedback current，The debounce time is the duration of this continuous detection.，exceed this time，Detect that the main motor current still exceeds the stop current，walkThe motor will stop；Otherwise, the walking motor will continue to move forward；

stop current:The feedback current of the main motor exceeds this value，The walking motor will stop；Unit Ampere；

Offset default:The initial value of the speed limit of the traveling motor when the remote control is turned on = 50% of this value；

Receiver operating power supply	DC24V/1A (independent power supply)
Receiver output point load	AC0-250V/3A DC0-30V/5A
Receiver speed regulation output voltage	DC0-10V