Floor grinder wireless remote control DH22ST-Le

Description

model：DH22ST-Le

Adaptive equipment：Floor grinder

Remark：Three types of antennas can be selected，The default suction cup antenna is equipped with standard

急停：急停按钮被拍下，请释放急停按钮

Low pressure：The battery of the remote control is too low，Please replace the battery

Fall out of the internet：Wireless signal interruption，Please check the receiver power supply，Power on again，Restart the remote control

1、Remote control turned on

The receiver is powered on，The RF-LED light on the receiver starts to flash；Two No. 5 batteries installed on the remote control，Turn on the power switch，Display display motor speed，It means the startup is successful。

2、照明

按一下“照明”按钮，接收器照明输出打开，显示屏出现照明图标

再次按一下“照明”按钮，接收器照明输出关闭，显示屏照片图标消失。

3、研磨电机和调速

Turn the "Forward/Reverse" switch to forward，接收器研磨正转打开，The display displays forward rotation

Turn the "Forward/Reverse" switch to reverse，接收器研磨反转打开，Display display inversion

旋转“研磨调速”旋钮，可以调节接收器研磨调速输出电压大小0-10V；

4、行走电机和调速

Turn the "Forward/Reverse" switch to forward，Receiver Revolver Progress and Right Progress Open，Display forward

Turn the "Forward/Reverse" switch to the back，Receiver reversal and right wheel reversal open，Display back

旋转“行走调速”旋钮，可以调节接收器左轮和右轮调速输出电压大小0-10V；

5、Turn left and right

Turn the "Left/Right" switch to the left，Receiver right wheel advances to open，The display display turns left

Turn the "Left/Right" switch to the right，Receiver revolver advance opens，The display display turns right

6、Turning in place

Turn left in place：Press and hold the Enable button，将“左转/右转”开关扳到左转位置，接收器左轮后退和右轮前进打开，Start turning left in place；

Turn right in place：Press and hold the Enable button，将“左转/右转”开关扳到右转位置，接收器左轮前进和右轮后退打开，Start turning right in place；

7、急停

Take the emergency stop button，接收器急停输出断开；所有开关控制断开，所有速度清零；

8、Straight line correction

When the left and right motor is moving forward and backward，There is a difference in the left and right speeds，Straight-line walking is offset，The linear deviation correction function of the remote control can be used，Fine-tune the speed of left and right wheels；

Principle of correction：Through bias correction function，Fine-tune revolver speed，To achieve the same speed as the right wheel，Realize the synchronization of left and right wheel speeds，Eliminate offsets；

Correction operation method：Press and hold the Enable button，缓慢旋转“直线纠偏”旋钮；

Rotate clockwise，Increase the revolver speed voltage，Increased deviation correction value of the display screen；

Rotate counterclockwise，Reduce the revolver speed voltage，The display deviation correction value is reduced；

Correction range：Correction value -90 to 90；1个纠偏单位的纠偏电压大约0.04V；

9、Parameter menu (user prohibits private modification)

进入参数菜单方式：研磨为0时，正转/反转连续上掰3次，再下掰3次；

退出方式：选择保存或者不保存，Press the enable button to confirm；

直线微调范围：0-120；

研磨速度：0-3000；

行走速度：0-1000；

Receiver operating power supply	DC24V/1A (independent power supply)
Receiver output point load	AC0-250V/3A DC0-30V/5A
Receiver speed regulation output voltage	DC0-10V